Publicité
Les langues disponibles
Les langues disponibles
USE & CARE
Fan Controls:
HAF18 Fans
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID
This fan provides a gentle flow of air ideal for use in the greenhouse industry.
STATE SPEED CONTROL DEVICE.
MOUNTING THE FAN
The fan comes complete with a 115V cord & plug. A suitable outlet needs to be located in a suitable location near the fan.
MAKE SURE POWER IS OFF BEFORE ATTEMPTING INSTALLATION.
Your "HAF" fan comes with a flat bar mount and pivot bracket. When suspended, the fan can pivot up and down and swivel 360˚
WARNING:
for optimal control of air stream. The first bracket can be suspended with flat bar or connected directly to the building structure.
These are assembled to fan as shown in Diagram 1 and should be bolted securely to the building structure.
ALL WIRING SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN FOLLOWING LOCAL CODES
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE BRACKETS WHEN INSTALLING THE
AND REGULATIONS.
BRACKETS, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN BETWEEN
ROTATING FAN BLADES.
CAUTION:
DIAGRAM 1
TIE OFF THE EXCESS CORD SO THAT IT WILL NOT GET CUT IN THE FAN.
Attach to overhead
joist or beam
MAINTENANCE
!
WARNING:
MOTORS ARE EQUIPPED WITH AUTOMATIC OVERLOAD PROTECTION AND MAY RESTART WITHOUT
WARNING. ALWAYS DISCONNECT FROM POWER BEFORE ATTEMPTING TO SERVICE.
Moving parts,
Fan
disconnect power
before servicing.
These fans are used in a variety of applications and therefore maintenance schedules will vary. In general no more than 1/16" of dirt
build-up should occur on blade, motor and guard for proper fan operation and to prevent premature failure. The complete fan should
be wiped down on a regular basis to maintain the high efficiency of the fan. Particular care should be taken to clean fan blades front
and back, and guards for better air moving performance. The motor should be kept clean to prevent overheating and premature failure.
As with all mechanical equipment scheduled inspections should include checking that all hardware is secure and blade set screws are
tight. We suggest as a minimum, that this be performed at the start and twice more every season.
WARNING:
THE FAN MUST BE MOUNTED TO THE BUILDING STRUCTURE.
WARNING:
THE STRUCTURE MUST BE SUITABLE TO SUPPORT THE WEIGHT OF THE FAN.
DO NOT PRESSURE WASH THE MOTOR. THE MOTOR IS TOTALLY ENCLOSED, BUT IT IS NOT
SEALED.
Canarm Ltd. warrants every new fan to be free of defects and workmanship, to the extent that, within one year
from the date of purchase, Canarm Ltd. shall either repair or replace at Canarm's option, any unit or part
WARNING:
thereof, returned freight pre-paid, and found to be defective. Proof of purchase may be required.
WARNING:
This warranty does not include any labor or transportation cost incidental to the removal and re-installation of
THE HARDWARE FOR MOUNTING TO JOIST OR BEAM IS NOT SUPPLIED. HARDWARE USED MUST
the unit at the users premises.
BE SUITABLE FOR THE TYPE OF JOIST OR BEAM TO WHICH THE FAN WILL BE MOUNTED.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
Components repaired or replaced are warranted through the remainder of the original warranty period only.
HARDWARE MUST CORRECTLY FIT THE MOUNTING HOLES PROVIDED AND SUPPORT THE
FOLLOWING:
This warranty applies to the original purchaser - user only; it is null and void in case of alteration, accident,
WEIGHT OF THE FAN.
A) Use this unit only in the manner intended by the manufacturer. If you have questions, contact
abuse, neglect, and operation not in accordance with instructions.
the manufacturer.
WARNING:
NOTICE: No warranty claims will be honored by Canarm Ltd. unless prior authorization is obtained.
B) Before servicing or cleaning unit, switch power off at service panel and lock the service
THE LOWEST PART OF THE FAN MUST BE AT LEAST 3 METERS (10 FT.) ABOVE THE FLOOR.
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
Installation or Product problems? Do not return to store of purchase.
tag to the service panel.
Contact Canarm Service at 1-800-265-1833 (CANADA) 1-800-267-4427 (U.S.A.)
WARNING:
1-800-567-2513 (EN FRANCAIS) Monday to Friday 8:00 - 5:00pm e.s.t.
FAILURE TO TIGHTEN ALL BOLTS & NUTS SECURELY COULD RESULT IN SERIOUS INJURY!
M-HAF18 - 04/13/16
M-HAF18 - 04/13/16
M-HAF18 - 11/09/17
READ INSTRUCTIONS COMPLETELY BEFORE INSTALLATION & SAVE FOR REFERENCE
HAF18 Fans
Instruction Manua
READ AND SAVE THESE INSTRUCTIONS
WARRANTY
CANARM LTD.
2157 PARKEDALE AVE. PO BOX 367
or visit www.canarm.com
BROCKVILLE, ONTARIO K6V 5V6
TELEPHONE: (613) 342-5424
FAX: 1-800-263-4598
E-MAIL: agsales@canarm.ca
l
CANARM LTEE.
2555 RUE BERNARD LEFEBVRE
LAVAL, QUEBEC H7C 0A5
TELEPHONE: (450) 665-2535
FAX: (450) 665-0910
E-MAIL: agsales@canarm.ca
Long Flat Plate
Bolt
Nut
Cotter Pin
ARTHUR MANUFACTURING FACILITY
#7686 CONCESSION 16, RR4
ARTHUR, ONTARIO N0G 1A0
TELEPHONE: (519) 848-3910
FAX: (519) 848-3948
Page 1 of 3
E-MAIL: agsales@canarm.ca
Page 3 of 3
Publicité
