Power Recliner With Headrest And Lumbar Assembly Instructions - La-Z-Boy Power Plus Mode D'emploi

Power Recliner with Headrest
and Lumbar Assembly Instructions
NOTICE:
-- To reduce the risk of product damage:
• Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remotes and three AAA batteries for the optional remote (F
WARNING
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
2. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
•
attached to the back (one on each side), to a 90° angle (F
Locate and identify the electrical connection between the back and the body. The color of the
•
connectors varies by date of manufacture.
The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
-
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
- The orange connectors on the left side (sitting) are for the adjustable lumbar feature. One connector
routes from bottom of the back panel and the other between the rear seat and tailgate.
Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
•
Connect the adjustable headrest (F
•
IGURE
push the connectors together and close the locking cover to secure the connection.
Connect the adjustable lumbar (F
•
IGURE
push the connectors together and close the locking cover to secure the connection.
3. Install the back.
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
•
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (F 2).
IGURE
Lower the back onto the body, making sure the back and body brackets are completely engaged.
•
To make sure the back is properly installed with both sets of back and body brackets
-
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (F
the steps above.
If you are unable to install the back properly, contact your La-Z-Boy
-
Lock the brackets by using a screwdriver to push down the locking levers (F
•
4. Remove the power supply from its packaging from the electrical components bag. Remove the power
supply and 120 volt power cord from the package.
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply
connector. Align the connectors, push together until fully seated and close the locking cover to
secure the connection (F 6).
IGURE
6. Connect the 120 volt power cord to the power supply (F
the operating instructions.
7. Proceed to the Battery Backup Assembly Instructions.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the motor connector behind the unit. Reverse the Assembly Instructions steps.
When lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully
to prevent damage to the electrical connections.
10
1).
IGURE
2 3).
IGURES AND
4). Align the pins and sockets in the brown connectors,
4). Align the pins and sockets in the orange connectors,
5). Remove the back and repeat
IGURE
dealer for assistance.
®
IGURE
6). Do not plug in until instructed in
IGURE
F
IGURE
Body
Bracket
F
IGURE
Back
Bracket
F
IGURE
3).
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Power Recliner with Headrest
and Lumbar Assembly Instructions
1 F
IGURE
Body
Bracket
Electrical
Components Bag
3 F
IGURE
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Adjustable Lumbar
Connection Orange
5 F
IGURE
120 Volt Power Cord
2
Back Bracket
Adjustable Headrest
4
Connection Brown
Tailgate Rear Seat
6
Motor Connector
Make this
connection
Make this
connection
Power Supply*
*Power supplies/connections
may vary by date of manufacture.
11