La-Z-Boy Power Plus Mode D'emploi page 25

Operating Instructions for
Optional Wireless Remote
To Program and Use Memory I or Memory II:
1. Use the remote to adjust the furniture to the best and most comfortable position for you.
2. Press and hold the Memory I or Memory II button for three (or more) seconds on either the remote or the cradle.
3. Listen for the "beep" and watch for the LED lights to flash on the remote to indicate the setting was
saved in memory.
• Memory I setting plays a single beep and flashes a single light to indicate a successful save.
• Memory II setting plays a double beep and flashes a double light to indicate a successful save.
• Three quick beeps and flashes of light are transmitted from the remote when the setting did
not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button (not holding
longer than two seconds), on either the remote or cradle. The furniture automatically moves to the saved
setting. If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing any button on the remote or cradle, while the furniture is in motion from a Memory button press, stops
the automatic movement of the furniture. The furniture does not restart once the button is released. Another
press of the Memory I or Memory II button is required to start the furniture in motion again.
If the Memory I or Memory II button is pressed on the remote and then the Do Not Disturb button (cradle) is
turned on, all motion stops. The furniture does not automatically resume and continue the move to a Memory I
or Memory II setting when the Do Not Disturb button is turned off. If the Memory I or Memory II button is pressed
on the cradle and then the Do Not Disturb button is pressed on the cradle, the furniture continues to move to the
stored setting. All Remote commands are ignored when Do Not Disturb is on.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to recline or extend,
except for the headrest.* When the headrest is programmed to extend, the headrest does not start in motion until
the back reaches approximately 40% recline, or its programmed recline setting if set to less than 40% recline.
This is done to guard against an undesirable positioning of the head and neck when moving into the stored
recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion battery
pack for the Memory feature to function. This feature is disabled when powered by the 9-volt battery backup.
Additionally, when powered by the optional rechargeable lithium-ion battery pack, only two features operate at
the same time.
To Use the Home Button:
The Home button returns the back is to its fully upright position and the legrest, headrest and optional lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back, legrest,
headrest and lumbar back to the upright and retracted positions.
All motion stops if any button is pressed while the furniture is moving to home. The motion does not resume
when the button is released. Another press and release of the Home button is required to restart the home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to the home
position first. Once the back and legrest are fully upright and retracted, then the headrest and lumbar return to
the retracted, home position. When powered by the optional rechargeable lithium-ion battery pack, the headrest
and lumbar move to the Home position first, and then the back and legrest move to Home.
48
Operating Instructions for
Optional Wireless Remote
To Use the Do Not Disturb:
Turning on the Do Not Disturb feature blocks the furniture's communication with the remote. When the remote is
blocked, the only features available for use are those with commands, or buttons on the cradle—these are the
Memory I, Memory II, Home and Find Me features.
Slide the Do Not Disturb button to the left (facing) position to turn on the feature and block out all commands
coming from the remote, allowing only the commands activated by a button press on the cradle. Slide the button
to the right position to turn off the feature and unblock the remote, allowing communication between the
furniture and remote.
To Use the Find Me:
Use this feature to locate a misplaced or lost remote.
Press and release the Find Me button on the cradle to send a signal to the remote. When the signal reaches the
remote, the remote LED lights start flashing and a loud tone plays continuously from the remote for two minutes,
or until any key is pressed on the remote. A key press on the remote when in Find Me mode does not produce
any movement, it only clears the Find Me response.
You can also clear the Find Me mode by pressing the Find Me button a second time, within two minutes of the
first press.
The Find Me mode is always enabled and works regardless if the Do Not Disturb feature is turned on or off.
Find Me mode is also enabled when the furniture is operating on the 9-volt battery back-up in the power supply,
or the optional rechargeable lithium-ion battery pack.
NOTE: For the Find Me feature to operate, the furniture must be powered, working batteries properly installed in
the remote and the remote within range of the furniture.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB cable
from the charging port when charging is complete. The USB port is for charging only and does not save or
transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB charge port is
disabled. When the furniture is powered by the optional rechargeable lithium-ion battery pack, the USB port
is enabled, as long as there is adequate charge.
49