Table Des Matières; Do Is Common And Do Is Connected To G0 - Regin OPTIGO OP10 Mode D'emploi

1 L
2
N
3
Fan start
COM
10
NO
11 DI2 40
NC
12 DI+ 41
DI1 42
G 43
13 UI+
DO
 DO1
14 UI1 44

15 DO2 A 50
GND
A 51
20 AI1
GND
AO1
21 A 52
GND
AO2
22 AI2 53
SPI 54
Figure 2. Wiring example: OP10-230 with water heating, 3-position output.
Supply air control with outdoor compensation and external setpoint device.
The digital outputs are 24 V AC, G is common and DO is connected to G0.
DO
For OP10, DO1 and DO2, the outputs can handle 12 VA. For OP10-230, DO1
and DO2, the outputs can handle 3.8 VA when using the internal transformer.
Control mode 4
L
1
2
N
3
Pump start
10 COM
NO
11 DI2
NC
12 DI+
DI1
G UI+
13
DO
 DO1
14 UI1
 DO2
15 A
GND
20 A AI1
GND
AO1
21 A
GND
AO2
22 AI2
SPI
Figure 3. Wiring example: OP10-230 with 3-position actuator and room
temperature sensor (can also be used without a room temperature sensor).
The digital outputs are 24 V AC, G is common and DO is connected to G0.
DO
For OP10, DO1 and DO2, the outputs can handle 12 VA. For OP10-230, DO1
and DO2, the outputs can handle 3.8 VA when using the internal transformer.
L 230 V AC
N
Control mode 5
Extended running
Fan indication
°C
Frost protection temp
°C
Supply air temp
°C
Outdoor temp
G0
Y1
G
Y
3
TG-R4/
4
PT1000
Figure 4. Wiring example: OP10 with 0...10 V actuator
The display menu system
The display menu system is divided into three levels, the configuration
level (10-second level), the clock and scheduler level (3-second level) and
the basic level.
The configuration level (10-second level)
This level is shown the first time the unit is connected. It is reached from
L 230 V AC
the Base Display (see the section The basic level below) by holding the
N
encoder button depressed for 10 seconds. The 10-second level holds
all the configuration menus. Note: The controller must display the Base
Display when pressing the encoder knob to reach the 10-second level.
40
41
42
43 °C
Room temp
44
50 °C Table 2 below shows how the 10-second level is organised. When you
Supply temp
51
enter the 10-second level, you will see menu level 0. Here, you choose
52
°C
Outdoor temp
53
the control mode. You navigate through the menus and control modes
54
by turning and clicking on the encoder knob. Different menus are shown
depending on the configuration.
Table 2. Display menus in the 10-second level
Menu
level
air temp.
control
0
G 1
24 V AC
10 COM 2
G0
11 NO
3
12 NC
DI2 40
DI+ 41
DI1 42
13 G UI+ 43
DO
14 DO1
UI1 44
15 DO2
A 50 °C
Supply water temp
GND
20 A
AI1 51
GND
21 AO1 52
A
GND
22 AO2
AI2 53
SPI 54
Control modes
1 2 3 4
Supply Supply Cascade Radiator
air temp. control control
contr. with with
outd. com- outdoor
pensation curve
OPTIGO OP10
Output type Output type
1
alt.
Actuating
Actuating
time
1.A
Output Output
signal signal
2
Neutr. zone Neutr. zone
3
P-band P-band
4
I-time
I-time
5
Damper Damper
minimum minimum
6 position position
6 -
Function for Function for
input UI1 input UI1
alt.
7
alt.
alt.
5
Domestic
hot water
control
Output type Output type
-
alt. alt. alt.
Actuating
Actuating
time time time
-
Output
signal
- -
Neutr. zone
- -
P-band P-band P-band
I-time I-time
I-time
Damper 0°C
minimum tempera-
position ture boost D-factor
P-band
cascade
- - -
Function for
input UI1
alt. alt.
alt.
alt.
Pump Over-
. exercise heating
alt. alt
3