Tipping Lever For Grass Catcher (If Available, Only For Models With Rear Grass Catcher); Pushbutton Panel - Stiga MPST 84 Li 48 V1 Manuel D'utilisation

Tondeuse à gazon à conducteur assis, alimentation par batterie
Masquer les pouces Voir aussi pour MPST 84 Li 48 V1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

6.8 TIPPING LEVER FOR GRASS
CATCHER (IF AVAILABLE,
ONLY FOR MODELS WITH
REAR GRASS CATCHER)
This lever, removable from its seat, 
allows the grass catcher to be overturned 
for emptying, reducing the effort 
required by the operator (fig. 12.E).

6.9 PUSHBUTTON PANEL

Depending on the model, the 
machine can be equipped with one 
of the pushbutton panel versions
(fig. 12.C, fig. 12.D and fig. 12.L) described
below: :
6.9.1 Pushbutton panel (type "I") fig. 13
Machine start button
With the key fully inserted this 
button (fig. 13.A) turns the machine 
ON and enables all functions.
NOTE
If all safety conditions are met, 
the "READY" icon comes ON 
(fig. 13.K) and the machine is 
ready to be used (see par. 7.4).
Cutting means engage and
disengage pushbutton
Press the button fig. 13.B to engage/
disengage the cutting means.
• When the cutting means 
are engaged, they become 
operational after a few seconds.
•   When the cutting means are 
disengaged, a brake is applied 
simultaneously to stop them 
rotating after a few seconds. 
NOTE
If the cutting means are engaged 
without taking the necessary 
safety precautions, the machine 
shuts down and cannot be 
restarted (see par. 7.2.2)
Reverse gear cutting
enable button
Holding down the button 
fig. 13.C gives consent
for reverse mowing.
For reverse cutting, engage the
cutting means and simultaneously 
hold down the button. 
NOTE
A single buzzer signal indicates the
lack of consent for reverse cutting.
Beacon ON button
Pushing the button fig. 13.D turns
the beacon on/off.
When the beacons are ON,
icon fig. 13.L is illuminated
Attention icon
If icon fig. 13.E is illuminated, it 
this indicates failure to comply 
with safety conditions or a 
possible malfunction of the 
machine (see chap. 15).
Battery LED
The LEDs fig. 13.F generally 
indicate the charge level of the
machine's batteries but in particular 
combinations their lighting status 
provides information about machine 
malfunctions (see chap. 15).
"Ready" icon
The icon in fig. 13.K is 
illuminated when the machine 
is ON and ready to be used.
"Bluetooth" icon
The icon in fig. 13.M is illuminated 
when the machine and the data 
exchange device are connected.
Controller and/or motor
over-temperature icon
The icon in fig. 13.N indicates 
overheating of electrical
components. See chap. 15.
Transmission engagement /
disengagement lever icon
The icon in fig. 13.O is illuminated 
when the transmission is not 
engaged (see par. 6.3 and chap. 15).
Operator on-board icon
The icon in fig. 13.P is illuminated 
when operator leaves the 
driving seat (see par. 7.2.2).
EN - 14

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mps 84 li 48 v1Mpns 84 li 48 v1Mp 84 li 48 v1Mpx 84 li 48 v1Mpst 84 li 48 v2Mps 84 li 48 v2 ... Afficher tout

Table des Matières