Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
manualeTHERAPYQUICKcompl
9-11-2007
GB
3 Getting Started
3.1
1. The block battery supplied must first be inserted in the battery
compartment before the unit can be used for the first time.
Inserting / removing
2. Check that the unit is switched off. Turn both intensity controllers,
batteries
15
and
9
, anti-clockwise to the OFF position.
3. Open the battery compartment
12
downwards. At the same time press down with the thumb
on the area of the cover identified with raised dots.
4. Insert the battery in the base of the battery compartment taking
care to match up the symbols (+ / -). Thread the textile strip
under the battery; this will make it easier to remove the battery
the next time it needs replacing.
5. Close the battery compartment by placing the cover on the lateral
guides and sliding it upwards with slight pressure of the thumb
on the area marked.
6. Follow the same procedure when replacing the battery at a later
date. Always use only 9 V block batteries of type 6LR61.
BATTERY SAFETY INFORMATION
• Keep away from children.
• Do not short-circuit.
• Do not dispose of old batteries with your household waste,
but dispose of them at a battery collection station at a
recycling site or in a shop.
Battery compartment
1. Lay the belt
3.2
so that the four pad markings are visible.
Preparing the belt
2. Lay out the electrode pads
for use
connectors
1
3. The unit is supplied with 4 (2 x 2) self-adhesive pads on a
backing or protective film which correspond in size to the
markings on the belt.
Use scissors to cut carefully between the two pads on the film
marked "on" without separating the pads from the film. There
will now be four pads in front of you.
4. Remove the two-part protective films from the sides of pads
7
with a criss-cross pattern by pulling the films off carefully from
the inside outwards. Leave the films marked "on" on the pads.
5. Position the pads
down, centrally on the markings on the belt. Press the pads
down firmly onto the belt.
WARNING
Only use the belt when all four pads are attached to the
electrodes to prevent unpleasant electric shocks.
Insert pads centrally on
the areas marked.
6
15:06
Pagina 4
11
by pushing the keypad cover
• Do not recharge.
• Do not throw into fire.
4
flat on a table with the electrode side upwards
6
and
7
and the pushbutton
and
3
with their connection cables.
6
and
7
with the criss-cross patterned side
channel 1
channel 2
3.3
Adjusting the belt
width
6
and
3 Getting Started
NOTES
Use only the original MANIQUICK electrodes enclosed
with the unit. Use separate electrode pads for each user.
These may be ordered subsequently from MANIQUICK
as a pad set.
For the first few applications, the electrode pads are very
sticky. It is, therefore, advisable to remove the electrode
pads carefully from the skin with the belt.
6. Turn the belt over and place it flat on the table again with the self-
adhesive pads facing downwards. The four pushbutton contacts
are visible.
7. Take the cables and connect the two pushbutton connectors
to the pushbutton contacts as shown in the diagram. Do the
same with pushbutton connectors
3
.
CAUTION
Make sure that the two intensity controllers
in the OFF position before inserting the cables.
8. Insert the free ends of the cables into the connection sockets of
channel 1 and 2 (
16
and
8
) on the top of the TENS unit. It is
immaterial which cable is assigned to which channel.
The belt
4
is a universal size which fits everyone. The belt width may
be adjusted to suit the individual by fixing the Velcro fastener
GB
1
5
and
9
are
5
.
7
Publicité
Table des Matières
