Description Of The Appliance; Assembly - Kärcher K 5 Premium Mode D'emploi

Description of the Appliance

These operating instructions describe the maximum
equipment. Depending on the model, there are differ-
ences in the scopes of delivery (see packaging).
Illustrations on Page 2
1 Coupling element for water connection
2 Storage for trigger gun
3 Water connection with integrated sieve
4 Appliance switch „0/OFF" / „I/ON"
5 High pressure hose
6 Dosage regulator for detergent
7 Storage for trigger gun
8 High-pressure hose drum
9 Transport handle
10 Hand crank for hose drum
11 Storage of Plug 'n' Clean detergent bottle with de-
tergent connection
12 Storage for spray lance
13 Storage hook for mains connection cable
14 Mains cable with mains plug
15 Plug 'n' Clean detergent bottle with locking lid
16 Bearing wheel
17 Trigger gun
18 Lock trigger gun
19 Key to detach the high pressure hose from the trig-
ger gun
20 Spray lance with pressure regulation (Vario Power)
Carrying out the most common cleaning tasks.
The working pressure can be continuously in-
creased from "SOFT" to "HARD". To adjust the
working pressure, release the trigger gun lever and
turn the spray lance to the desired position.
Suitable for use with detergents.
21 Spray lance with Dirtblaster
For strong contaminations.
* Optional
22 Washing brush
Suitable for use with detergents.
23 Rotary washing brush
Especially suitable for cleaning cars.
24 Foam nozzle with detergent container
With powerful foam for effortless cleaning.
** Additionally required
25 Fabric-reinforced water hose with commercially
available coupling.
– Minimum diameter, 1/2 inches (13 mm).
– Minimum length 7.5 m.
12
Mount loose parts delivered with appliance prior to start-
up.
Illustrations on fold-out pages!
Install wheels
Illustration
 Push the wheels into the intake and secure them
with the plugs. Align the plug properly.
Install the storage for trigger gun
Illustration
 Place the bottom holder into the recesses and push
forward until it audibly locks in.
 Insert the top holder and push down all the way.
Install the storage hook for the mains connection
cable
Illustration
 Press in the storage hook and lock it into the top po-
sition.
Install the transport handle
You will need the 2 included screws as well as a Phillips
screwdriver PH 2.
Illustration
 Slide the transport handle into the guide and se-
cure it with 2 screws.
Install the dosage regulator for detergent
You will need the 2 included screws as well as a Phillips
screwdriver PH 2.
Illustration
 Insert both detergent hoses onto the hose fittings.
 Install the dosage regulator and connect using 2
screws.
Note: During installation you must make sure that
the tongues of the dosage regulator match up with
the intended recesses in the casing.
Install the high pressure hose drum
Illustration
 Slide the free end of the coiled high pressure hose
through the recesses on the dosage regulator.
 Insert the hose drum into the intakes on the trans-
port handle.
 Insert the axle of the hand crank into the guides.
 Install the fixating plate and secure it using 2
screws.
 Press the connecting fitting from the short high
pressure hose into the brass intake, secure with
clamps.
Note: Make sure the connection nipple is aligned
correctly.
Connect the high pressure hose to the trigger gun
Illustration
 Push the high pressure hose into the trigger gun
until it locks audibly.
Note: Make sure the connection nipple is aligned
correctly.
Check the secure connection by pulling on the high
pressure hose.
Installing coupling
Illustration
 Screw the coupling element to the water connec-
tion on the appliance.
– 6
EN

Assembly