Assign Primary Zones; Set Low Or High End - Grafik Eye 4000 Serie Mode D'emploi

Assign Primary Zones

See page 25 for the Control Directory worksheets for recording zone
assignments.
A. Press and hold buttons 1 and 5 until the Select Value LED flashes once per
second.
B. Press button 5 repeatedly until the Zone Assignment w/Circuit Schedule
LED lights.
C. Select the primary zone assignment.
For GRX 4000 Series: Press button 3 or 4 to select both control unit and
zone assignment. Example: If the control desired is addressed to 'A2' and
the zone desired is the 3rd from the left, use buttons 3 and 4 to get 'A23'
as a value for the appropriate circuit.
For DMX512: (2Link only) Press button 3 or 4 to select zone assignment
(1-512).
D. Use buttons 1 and 2 to change to the next circuit, then repeat Step C. Do
this for all affected circuits. Record each circuit's control and zone on a
Circuit Directory.
E. Press and hold buttons 1 and 5 until the View Value LED lights.
Notes
• The circuit selector's display will go out automatically 20 minutes after the
last button press.
• More than one circuit can be assigned to the same zone.
• Zone Capture™ is an alternate method for assigning zones. It is described on the opposite page.
• 2Link only- The Link A and Link B LEDs located next to the Value window indicate which link is being assigned as
per the hierarchy. To set the hierarchy, see page 15.

Set Low or High End

Note: Low end and high end light levels are set automatically when load type is assigned. This step is to be done if
the default settings need to be changed.
Warning! Do not reduce the low end or increase the high end on a fluorescent load type. This will decrease
lamp life and may damage the ballasts. Do not increase the high end of neon/cold cathode. This may
overdrive the lamps and cause decreased tube life.
To change the setting:
A. Press and hold buttons 1 and 5 until the Select Value LED
lights.
B. Press button 5 repeatedly until the Low End Trim LED or the
High End Trim LED lights.
C. Use buttons 1 and 2 to go to the circuit that needs to be
changed.
D. Use buttons 3 and 4 to reset the trim as desired. The load
will go to the new setting while in this mode despite the
GRX control's intensity.
Notes
• Low end and high end ranges are limited to avoid
overlapping.
• '1' is the minimum low end and '99' is the maximum high
end.
• 'Value' is a relative number. It is not a % intensity, but
rather a reference point to help set other circuits, if desired.
Record the new trim setting on a Circuit Directory so that it
is documented.
E. Use buttons 1 and 2 to go to another circuit that needs to be changed and repeat Step D.
F. Press and hold buttons 1 and 5 until the VIEW VALUE LED lights.
Note: The circuit selector's display will go out automatically 20 minutes after the last button press.
R
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
Load Type Quick Reference:
--- Unassigned
1-1
2-1
2-2
LINK 1
Load Type Quick Reference:
--- Unassigned
1-1
2-1
2-2
LINK 1
1 2 3 4 D 5
Data A OK
1 2 3 4 5
D
S C
ELECT IRCUIT
Circuit
V V
IEW ALUE
S V
ELECT ALUE
Link A
Link B
S V
ELECT ALUE
Circuit Level
Load Type
(See Instructions)
Zone Assignment
Zone Assignment
Low-End Trim
High-End Trim
Address
('Ad' displayed)
Warning - Read instructions to set the Load
Type. Instructions show more load types.
Load Type Quick Reference:
--- Unassigned
1-1 Incandescent
2-1 Fluorescent Lutron Hi-lume
2-2 Fluorescent Lutron Tu-Wire
GRAFIK Eye 4000 Series Control Unit Installer's Guide 13
®
D 5
C
D
Data A OK Power OK Data B OK
Link Link
A B
D 5 C D
S C
ELECT IRCUIT
1
Steps A and
2
Circuit
E: Press and
V V
IEW ALUE
hold Buttons
S V
ELECT ALUE
1 and 5
Link A 3
Link B
4
Value
S V D
ELECT ALUE ISPLAYED
Circuit Level
5
Load Type
(See Instructions)
D 5 C
D
Zone Assignment
w/ Circuit Schedule
Zone Assignment
w/ Zone Capture
TM
Low-End Trim
Data A OK Power OK Data B OK
High-End Trim
Address
('Ad' displayed)
Link Link
Warning - Read instructions to set the Load A B
Type. Instructions show more load types.
5
D C D
S C
ELECT IRCUIT
3-1 Neon / CC
1
Incandescent 4-1 Non-Dim
Fluorescent Lutron Hi-lume FDB Ballast
2
R
Fluorescent Lutron Tu-Wire Ballast
Circuit TM
V V
IEW ALUE
S V
ELECT ALUE
Value window
Link A 3
Link B
4
Value
S V D
ELECT ALUE ISPLAYED
Circuit Level
5
Load Type
(See Instructions)
Zone Assignment
LINK 2 (Non-Ess) w/ Circuit Schedule (Essential)
Zone Assignment
w/ Zone Capture
Normal Emergency
TM
Low-End Trim
High-End Trim
Address
('Ad' displayed)
Warning - Read instructions to set the Load
Type. Instructions show more load types.
3-1 Neon / CC
Incandescent 4-1 Non-Dim
Fluorescent Lutron Hi-lume FDB Ballast
R
Fluorescent Lutron Tu-Wire Ballast
TM
LINK 2 (Non-Ess) (Essential)
Normal Emergency
C
D
Power OK Data B OK
Link Link
A B
C D
1
2
Steps A and
F: Press and
hold Buttons
1 and 5
3
4
Value
D
ISPLAYED
5
w/ Circuit Schedule
w/ Zone Capture
TM
3-1 Neon / CC
4-1 Non-Dim
FDB Ballast
R
Ballast
TM