Technical Data; Proper Use; Before Starting The Equipment - EINHELL BG-EM 930 Mode D'emploi

Anleitung_BG_EM_930_SPK1:_
2. Explanation of the warning signs on
the equipment (see Fig. 8)
1 = Read the directions for use before operating the
equipment
2 = Wear ear guards and goggles
3 = Keep all other persons away from the danger
zone.
4 = Caution! -Sharp blades- Before carrying out any
maintenance work or if you damage the cable,
pull the plug out of the socket.
5 = Caution: The cutters continue to run after the
motor is switched off
6 = Do not expose the equipment to rain or moisture.
7 = Caution: Keep the power cable away from the
cutters!
3. Layout (Fig. 1 / 2)
1. ON/OFF switch
2. Cable strain-relief clamp
3. Carry handle
4. Grass basket
5. Ejector flap
6. Mains plug
7. Top push bar
8. Bottom push bar
9. Fastening screws for bottom push bar
10. Fastening screws for top push bar
11. Cable clips
12. Grass box housing halves
13. Grass box handle

4. Proper use

The lawn mower if designed for use in private
gardens.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
26.09.2007 10:17 Uhr Seite 15

5. Technical data

Voltage:
Power input:
Motor speed:
Cutting width:
Cutting height adjustment:
Volume of catch bag:
L sound pressure level:
pA
L sound power level:
WA
Vibration at the handlebars a
Protection class

6. Before starting the equipment

The lawn mower is delivered unassembled. The
complete push bar and the grass collector must be
assembled before using the lawn mower. Follow the
operating instructions step-by-step and use the
pictures provided as a visual guide to easily
assemble the machine.
6.1 Fitting the push bar (Fig. 3a to 3d)
Fit a bottom push bar (Fig. 3a / Item 8) into the
opening provided for it (Fig. 3a) and secure it as
shown in Fig. 3b with a screw (Fig. 3b / Item 9).
Proceed in the same way on the other side.
When you fit the top push bar you can decide the
height of the push bar by selecting the appropriate
fastening hole (Fig. 3c). Fasten the top push bar
using either the holes L for a low position or H for a
high position. Screw the top push bar to the bottom
push bar as shown in Fig. 3d.
6.2 Fitting the grass box (Fig. 4a to 4f)
Fit the two halves of the grass box together (Fig. 4a /
Item 12). The two halves are identical. Ensure that all
the plastic lugs engage correctly (Fig. 4b). Next push
the grass box handle (Fig. 4c / Item 13) into the
openings on the grass box. Check that the handle is
secure and correctly positioned as shown in Fig. 4d.
Before you fit the grass bag you must ensure that the
motor is switched off and the blade is not rotating.
The grass box must be attached to the two hooks on
the mower (Fig. 4e / Item A). To do this, open the
ejector flap with one hand (Fig. 4f / Item 5) and attach
the grass box with the other hand as shown in Fig. 4f.
The ejector flap is held against the grass box by a
spring.
GB
230 V ~ 50 Hz
900 watts
3600 rpm
30 cm
25-60 mm; 3 levels
28 liters
72,8 dB(A)
96 dB(A)
: < 2,5 m/s 2
hv
II/®
15