Replacing The Blade; Servicing The Wheels (Illustration S ); Troubleshooting; Technical Data - Sabo 43-EL COMPACT Livret D'entretien

Replacing the blade

WARNING
The cutter bar must always be replaced by an authorised workshop since an
insulation protection test always has to be carried out after repairs and
maintenance work on insulation parts (e.g. blade screw) in accordance with the
applicable standard DIN EN 60335.
In addition, a wrongly assembled cutting blade coupling can allow the cutter bar
to become loose, which can lead to serious injuries.
– Only use genuine cutter bars for replacement. Non-equivalent spare parts can
damage the machine and are a safety hazard.
– Replacement cutting tool must be marked permanently with the name and/or
company logo of the manufacturer or supplier and the part number.

Servicing the wheels (Illustration S )

Lubricate the wheel bearings once a year or every 15-20 operating hours.
– Remove the wheel caps S .
– Use a socket wrench to loosen the hexagon nut, washer and wheels.
– After the bearings have been lubricated with roller bearing grease "KAJO-Longlife
grease LZR 2", push the wheels back in place, replace the washer, fix the hexagon
nut and tighten until the wheels can just about turn easily but without play. Replace
the wheel caps.

17 TROUBLESHOOTING

Fault Possible cause
No power supply.
If the motor does not
start 5 seconds after
the unit is started
Power cable damaged.
Cutting height has been
set too low (grass is too
high and blocks the
starting of the motor).
Too much grass waste in
the housing.
Extreme vibration
Blade blunt.
Unclean cut, lawn is
yellow
Cutting height too low.
Mowing too fast.
Insufficient overlapping
of cuts when mowing.
Lawn becomes matted.
Turbo signal has not
Ejection blocked
been detected
J + K .
Cutting height too low for
grass that is too high.
Pushing mower too fast.
Grass not dry.
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
maintenance work described here yourself.

18 TECHNICAL DATA

Motor

Mower

Remedy
Connect the plug C2 .
Check the fuse.
Get it checked by an
authorised workshop.
Set a higher cutting height I .
Machine tilts when starting it.

Sound power level

Clean the cutting chamber of
grass, ensure that the gap

Sound pressure level

between fan and housing is
kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.

Vibrations

Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorized
dealer Q .
Adjust to higher cutting height

19 ORIGINAL SPARE PARTS

I .
Adjust mowing speed.
Tall grass conditions may
dictate that more overlapping
of cuts is required.
A lawn scarifier can remedy
the problem considerably
Empty the grass collector L .
Adjust to higher cutting height
I .
Adjust mowing speed.
Let grass dry.
9
Motor
Connection voltage
Power
Motor speed
Housing
Cutting width
Cutting heights
Adjustable-height handlebar
Grass collector capacity
Weight
Length
Width
Height
Wheels front / rear
Bearing front
Bearing rear
Guaranteed sound power level;
measured according to 2000/14/EC
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
Vibrations on the lawnmower's handlebar;
measured according to EN 60335-2-77
Measuring inaccuracy; according to EN12096
Roller bearing grease
Cutter bar
Alternating current motor
230 V
1500 W
3000 min
Die-cast aluminium
430 mm
Central, 22, 30, 35, 42, 50, 60, 80 mm
3-way
55 litres
27 kg
1480 mm
500 mm
1000 mm
Ø 180 mm / Ø 180 mm
Cup-and-cone bearing
Cup-and-cone bearing
L = 96 dB(A)
wa
L = 82 dB(A)
pA
1.5 dB
a = 1 m/s
hW
0.5 m/s
SAA11300
For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.
-1
2
2