Operation; Working With The Chainsaw Mounting Kit - EINHELL GE-HC 18 Li T Traduction Du Mode D'emploi D'origine

5.9 Turning the chain saw mounting kit
through 90° on the motor head (Fig. 22)
The cutter rail guard must be slipped over the
mounted cutter rail with saw chain in order to
prevent injuries.
1. Pull the lock button (26) to the right.
2. Turn the chain saw mounting kit 90° counter-
clockwise. The chain saw mounting kit will
lock onto the motor head and is then secured
in place.
5.10 Removing the chain saw mounting kit
from the motor head (Fig. 20 – 21)
The cutter rail guard must be slipped over the
mounted cutter rail with saw chain in order to
prevent injuries.
1. Pull the lock button (26) to the right.
2. Turn the chain saw mounting kit to the point
where the arrows on the motor head and
chain saw mounting kit coincide, allowing the
mounting kit to be removed.
5.11 Fitting the battery (Fig. 23 – 24)
Press the side pushlock button (32) of the battery
pack as shown in Fig. 23 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 24, make sure that
the pushlock button latches in place! To remove
the battery pack, proceed in reverse order.

6. Operation

Please note that the statutory regulations
governing noise abatement may diff er from one
location to another.
Caution! Always use the shoulder strap when
working with the equipment. Always switch off the
equipment before you take off the shoulder strap.
(Otherwise there is a risk of injury.)
Put on the shoulder strap as described above,
fi t the required mounting kit and adjust the
equipment to suit your needs.
Switching on/off
Switching on
•
Hold the equipment by the handles with both
hands (thumbs under the additional handle).
•
Slide the safety lock-off (Fig. 3/Item 3) to the
front and hold.
•
Switch on the equipment with the On/Off
switch (Fig. 3/Item 2). You can then release
Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 15 Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 15
EN
the safety lock-off.
Switching off
Release the On/Off switch (Fig. 3/Item 2).
6.1 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Battery capacity indicator (Fig. 25 / item
33)
Press the battery capacity indicator switch (34).
The battery capacity indicator (33) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
7. Working with the chainsaw
mounting kit
Preparations
To ensure that you can work safely, check the
following points before every use and in the event
of any damage:
Condition of the chainsaw
Inspect the chainsaw before the start of work for
damage to the housing, the power cable, the saw
chain and the cutter rail. Never use a chainsaw
which is obviously damaged.
Oil container
Level of oil in the oil container: Both before and
during your work make sure that there is always
suffi cient oil in the system. To avoid damaging the
chainsaw, never run the saw if there is no oil in the
system or if the oil drops below the "min" mark.
On average, a single fi lling will last around 20
minutes depending on the number of pauses in
cutting and the loads involved.
- 15 -
19.03.2019 14:48:49 19.03.2019 14:48:49