EINHELL GE-HC 18 Li T Traduction Du Mode D'emploi D'origine page 14

5.2.c Saw chain lubrication
Caution! Always remove the battery from the
device before inspection and adjustment. Always
wear protective gloves when working on the
chainsaw to protect yourself against injury.
Important! Never operate the chain if it is not
lubricated with saw chain oil. Use of the chainsaw
without saw chain oil or if the oil level is below
the viewing window will result in damage to the
chainsaw!
Important! Be aware of the temperature
conditions:
Diff erent lubricants with completely diff erent
viscosities are required at diff erent ambient
temperatures. At lower temperatures you will need
low viscosity oils in order to achieve a suffi cient
lubricating fi lm. However, if the same low viscosity
oil is used during the summer it will become even
thinner due to the ambient temperatures alone,
and as a result the lubricating fi lm could break
down, causing the chain to overheat and become
damaged. In addition, the chain oil would burn
and produce unnecessary pollutants.
Filling the oil tank (Fig. 12):
•
Place the chainsaw on a flat surface.
•
Clean the area around the oil tank cap (Fig.
12/Item 31) and then open the oil tank cap.
•
Fill the tank (Fig. 12/Item 30) with saw chain
oil. In the process, make sure that no dirt
enters the tank, as this could cause the oil
nozzle to become blocked.
•
Close the oil tank cap (Fig. 12/Item 31).
After the chain saw mounting kit has been fi tted
and when the equipment is not being used, slip
the cutter rail guard (Fig. 1/Item 17) over the
mounted cutter rail with saw chain in order to
prevent injuries.
5.3 Adjusting the additional handle (Fig. 13-
14)
a) Setting the tilt of the additional handle
Open the lock (22). Set the desired tilt of the
additional handle (8). Close the lock.
b) Shifting the additional handle
Open the lock and slide the additional handle (8)
into the required position. Close the lock.
Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 14 Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 14
EN
5.4 Using the shoulder strap
Warning! Always use the shoulder strap when
working with the equipment. Switch off the
equipment before you take off the shoulder strap
(Otherwise there is a risk of injury.)
1. Hook the carabiner (Fig. 4/Item A) into the
strap attachment (20).
2. Slip the shoulder strap (Fig. 15/Item 7) over
your shoulder.
3. Adjust the length of the shoulder strap so that
the strap attachment is at waist level (Fig. 15).
4. The shoulder strap is equipped with a buckle.
Press the hooks together (Fig. 16) if you need
to put down the equipment quickly.
5. To change the strap position on the
equipment, press together the two metal
loops on the strap attachment (Fig. 4/Item 20)
and adjust the strap attachment on the tube.
5.5. Adjusting the angle of the handle
(Fig. 17)
Press the two safety lock-off s (24) and adjust
the angle of the handle (1) to any of 4 latching
positions.
5.6. Adjusting the angle of the motor housing
(Fig. 18)
Press the two safety lock-off s (24) and adjust the
angle of the motor housing (25) to any of the 7
latching positions.
5.7 Adjusting the telescopic tube (Fig. 19)
1. Undo the telescopic tube lock nuts (9 + 11) by
turning them counter-clockwise.
2. Pull out the telescopic tubes (10 + 12) to suit
the required working height.
3. Secure the telescopic tube lock nuts (9 + 11)
by them turning clockwise.
5.8 Fitting the chain saw mounting kit to the
motor head (Fig. 20 – 21)
The cutter rail guard must be slipped over the
mounted cutter rail with saw chain in order to
prevent injuries.
1. Position the chain saw mounting kit and the
motor head such that the arrows on both
parts coincide.
2. Press the chain saw mounting kit against the
motor head. This will cause the lock button
(26) to be pushed to the right. Turn the chain
saw mounting kit clockwise. The chain saw
mounting kit will lock onto the motor head and
is then secured in place. This will cause the
lock button (26) to be pushed to the left.
- 14 -
19.03.2019 14:48:49 19.03.2019 14:48:49