Kettler Marathon TX1 Mode D'emploi page 11

GB Functions and operation of the TX1 training computer
by different profiles (different incline values over time).
If the user can set a program individually, the preset value (or
previously entered value) blinks and shows that you can either
confirm the blinking value or change the value. The treadmill
starts as soon as you have entered and confirmed your values.
1. Switch the unit on.
2. Secure the safety key to the treadmill and the clip to
the user's clothing.
3. Press the PROGRAM button four times for P4, five
times for P5, or six times for P6 = INLINE INTERVAL..
4. Press the ENTER button to confirm the selected program.
5. Use the STEIGUNG INCLINE buttons (+), (–) or the
SPEED buttons (+), (–) to enter the training time
6. Press the ENTER button to confirm.
7. Use the STEIGUNG INCLINE buttons (+), (–) or the
SPEED buttons (+), (–) to enter the intensity level based on maxi-
mum incline.
8. Press the ENTER button to confirm. The training now begins.
P4 IN C LIN E IN T ER VA L
1 2
1 0
8
6
4
2
0
T IM E (1 5 m in - 9 0 m in )
P5 IN C LIN E IN T ER VA L
1 2
1 0
8
6
4
2
0
T IM E (1 5 m in - 9 0 m in )
SPEED PROGRAMS P6, P7
Once the device is switched on and the safety key securely
inserted, you can press the PROGRAM button to select one of
the preset speed programs P6, P7. The speed programs differ
by different profiles (different speeds over time). If the user can
set a program individually, the preset value (or previously enter-
ed value) blinks and shows that you can either confirm the blin-
king value or change the value. The treadmill starts as soon as
you have entered and confirmed your values.
1. Switch the unit on.
2. Secure the safety key to the treadmill and the clip to
the user's clothing.
3. Press the PROGRAM button six times for P6 or seven
times for P7 = SPEED INTERVAL.
4. Press the ENTER button to confirm the selected program.
5. Use the STEIGUNG INCLINE buttons (+), (–) or the
SPEED buttons (+), (–) to enter the training time.
6. Press the ENTER button to confirm.
7. Use the STEIGUNG INCLINE buttons (+), (–) or the
SPEED buttons (+), (–) to enter the intensity level based on maxi-
mum speed.
8. Press the ENTER button to confirm. The training now begins.
P6 SPEED IN T ER VA L
16
14
12
10
8
6
4
2
0
T IM E (1 5m in - 9 0 m in )
P7 SPEED IN T ER VA L
1 6
1 4
1 2
1 0
8
6
4
2
0
T IM E (1 5 m in - 9 0 m in )
HEART CONTROL PROGRAM P8 H-SI
The user can set the program individually on the basis of his tar-
get heart rate. Once the device is switched on and the safety
key securely inserted, you can press the PROGRAM button to
select the heart control program P8 H-SI. If the user can set a
program individually, the preset value (or previously entered
value) blinks and shows that you can either confirm the blinking
value or change the value. The treadmill starts as soon as you
have entered and confirmed your values
The treadmill automatically sets the incline or speed to reach
and sustain the user's target heart rate after approx. 5 minutes.
After these 5 minutes, only the speed will be automatically
changed to maintain the target heart rate. It will attempt to
maintain the target heart rate at a precision of +/_4 beats.
During training, the user can still manually set the speed or incli-
ne. During the training, the time will count down from the total
time that was set as time for the training and cool down.
After finishing training, the treadmill automatically enters the
cool down program. The cool down program is set to 4 minu-
tes. In the first two minutes, the speed and the incline are redu-
ced by 50 %. In the last two minutes, the speed is reduced
again by 50 % and the incline reduced to 0 %.
In order to use the heart control program, the user must wear a
chest belt.
1. Switch the unit on.
2. Secure the safety key to the treadmill and the clip to
the user's clothing.
3. Press the PROGRAM button eight times for H-SI =
HRC SPEED /.
4. Press the ENTER button to confirm.
5. Use the STEIGUNG INCLINE buttons (+), (–) or the
11