quadient IS-6000 Mode D'emploi page 2

IS-6000
postage and
rate section
• For more specific information about your
mailing system, see the User Guide.
kb.quadient.ca/is6000_ug_en
Applying postage
1
TO RESET PREVIOUS SETTINGS...
PRESS CLEAR OR WAKE
• To get back to default rate settings,
tap on the screen.
• If the system is asleep, press
to wake it up with default settings.
Thickness setting
There is a thin/thick mail latch under the top cover of the fee-
der. For normal operation, the lever will be to the left. However,
for processing a batch of thick mail, move the lever to the right,
especially if the thicker envelopes won't feed into the mail path.
1- Open the feeder
cover.
2- Change the lever
position:
- left for normal;
- right for thicker
mail
3- Close feeder
cover
Task bar
1
Imprint,
2
System
monitoring
section
Menu Mailbox Direct acces button
2a TO WEIGH YOUR MAIL...
USE THE DYNAMIC SCALE
• Tap and select
OR
2b
PUT YOUR MAIL ON THE SCALE
• By default the weighing platform and
are automatically selected.
Otherwise, tap then
•
Changing the ink tank
1- On the new ink tank, remove the protective
strips.
2- Open the ink tank drawer by pulling it towards
you.
3- Press on the blue release lever to disengage
the ink tank.
4- Pull out the old ink tank.
5- Insert the new ink tank,
then push it until you
hear the click.
6- Close the drawer. The
alignment
of the printing heads
starts automatically.
Getting to know your mailing system
Account 1
Imprint, postage and rate section
section
Rate display
3
Processing
modes
section
ERA Slogan All rate Rate favorite
selection selection favorites
3
CHOOSE RATE AND SERVICES
Current rate and selected services are displayed in this
area of the screen.
To change the rate and/or add services:
1- If Rate favorite button is pressed,
parameters of imprint are displayed
in the imprint details zone above.
2- Use Rate favorite button to select a
preset rate.
3- If Other rates button is pressed,
the following screen appears.
Use rate buttons 1 to 9 to select
an available Class and or Services,
or select Rate wizard.
4- Validate your selection to return to
the home screen.
If jamming occurs...
In the base:
1- Pull the release handle on the lower
assembly of the print Base.
2- Using your other hand, remove the
jammed envelopes.
If the jammed envelopes can not be
removed, perform the following.
3- Press on the blue release lever to
disengage the lower conveyor.
In the feeder:
1- Open the cover.
process
2- Gently remove jammed
envelopes.
3- Close the cover.
2
System
monitoring section
Date Postage amount
and weight
Inserter
control
Sealing mode
3
Processing
modes section
Other Date
shortcuts rates settings Quiet mode
4
IMPRINT PRINTING
If you want to print on a label or automatically seal the envelope, check additional
options below.
1- Press to start the motors of your Mailing Machine.
2- Insert the mail piece in the feeder loader, the
imprint printing position on the upper right side.
To print on labels:
1- Insert labels into the dispenser until you hear a
click, printing side facing the right.
2- Select mode .
3- Tap to enter the number of labels
To seal the envelopes:
or deactivate
Adding credit
1-
Press , and
follow instructions on
screen.
2-
Note: to complete this
operation successfully,
your postal services
account must have a
positive credit balance
3-
of the corresponding
amount.
Franking Reset
counter
Ink level items
ON/OFF
Switch
Sleep/wake
Credit PC connected
available
Credit
Moistening level Weighing type
PC toggle
Stops printing
Starts printing
Print offset Label printing
.
Tap on the screen to activate
the sealer.
Filling the sealer bottle
Remove the bottle
from its base and
turn it over.
Unscrew the cap
and fill the bottle
with water up to the
limit marks.
Screw on the cap
and put the bottle
back into place.