Bosch PMF Universal Serie Notice Originale page 15

OBJ_BUCH-2472-003.book Page 15 Monday, November 16, 2015 12:29 PM
Accessory
BIM plunge cut saw
blades, metal
HM-Riff segment
saw blade
HM-Riff delta plate Mortar, concrete remain-
Scraper, rigid
BIM serrated seg-
ment saw blade
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory loosen the screw
7 with the hex key 8 and remove the tool.
Mount the application tool/accessory (e.g. plunge cut saw
blade 6) in such a way on the tool holder 5 that the openings
of the tool engage into the cams of the tool holder.
For a safe and fatigue-free working position it is possible to
position the application tools/accessories in any snap-in posi-
tions on the tool holder. Position the tool in such a way that
the depressed centre points downwards (marking on the tool
is readable from above, see figure on the graphics page).
Use the screw 7 to fasten the application tool/accessory.
Tightly fasten the screw 7 with the hex key 8.
 Check the tight seating of the application tool/acces-
sory. Incorrect or not securely fastened application
tools/accessories can come loose during operation and
pose a hazard.
Mounting and Adjusting the Depth Stop
The depth stop 11 can be used when working with segment
saw blades, Riff-segment saw blades and segment blades.
If required, remove an already mounted application tool/ac-
cessory.
Slide the depth stop 11 over and beyond the tool holder 5 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
Bosch Power Tools
Material Application
Metal (e. g. unhardened Smaller separating and plunge cuts;
nails, screws, smaller pro- example: shortening narrow profiles, cutting fastening
files), non-ferrous metals elements such as staples
Grouting joints, soft wall Cutting and separating close to edges, in corners or hard to
tiles, glass-fibre reinforces reach areas;
plastic and other abrasive example: removing grouting joints between wall tiles for
materials repair work, cutting openings in tiles, gypsum boards or
plastic
Rasping and sanding on hard surfaces;
ders, wood, abrasive ma- example: removing mortar or tile adhesive (e.g. when
terials replacing damaged tiles)
Carpets, coverings Scraping on hard surfaces;
example: removing carpet and tile adhesive
Insulation material, insula- Cutting soft materials
tion panels, floor panels,
sound insulation panels,
cardboard, carpet, rub-
ber, leather
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 11 from the tool holder 5 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 11 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 11 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other ap-
plication tools, remove the depth stop 11. For this, remove
the application tool and pull the depth stop from the gear
head.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 9 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 10, free the Velcro back-
ing of the sanding plate 9 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 10 flush alongside one edge of the
sanding plate 9, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
English | 15
1 609 92A 1PP | (16.11.15)