Changing The Dust Bag - Bosch BSGL3 Serie Mode D'emploi

Using the dust container
!
Caution: The dust bag change indicator only works in
conjunction with a dust bag.
22
Figure
Set the power setting to maximum for the best results
when vacuuming.
We recommend that you reduce the setting only when
vacuuming very delicate materials.
Emptying the dust filter
To achieve an optimal result when vacuuming, the dust
container should be emptied each time the vacuum cleaner
is used.
23
Figure
Turn the dust compartment locking lever in the direction
of the arrow to open the dust compartment cover.
24
Figure
Remove the dust container from the appliance.
25
Figure
Release the two snap locks on the bottom flap in the
direction of the arrow, open the flap until it clicks
into the stop position and the container will then
empty the dirt in a downwards direction.
When closing the bottom flap, please ensure that
there is no dirt around the edges. Clean if neces-
sary.
Close the bottom flap, making sure that you hear it
click into place.
26
Figure
Put the dust container back into the appliance and
close the dust container lid.
Caution: the inside of the dust container may
!
become scratched with use and start to look
opaque. This does not, however, affect the perfor-
mance of the vacuum cleaner in any way, i.e. it will
continue to function as normal.
Cleaning the permanent filter and Microsan
filter in the dust container
The filters must be cleaned (wash out the filter sys-
tem):
After any malfunctions, i.e. after a blockage is
cleared.
At least every six months.
27
Figure
Press in the locking tab on the rear side of the con-
tainer and remove the Microsan filter from the con-
tainer.
Remove the permanent filter from the bottom plate
of the container.
28
Figure
Wash the Microsan and permanent filters. The filters
must then be left to dry for at least 24 hours.
After cleaning, insert the permanent filter into the
bottom plate of the container.
Put the Microsan filter onto the container and fix it
in place by pushing in the direction of the arrow.
You will hear the tab snap into place.
Malfunctions
Removing a blockage in the dust container.
29
Figure
Empty the container (see figure 25)
Loosen the blockage, e.g. with a screwdriver, and
tap it out.
Close the bottom flap, making sure that you hear it
click into place.
Using dust bags
If necessary, a dust bag may be used instead of the
dust container.
30
Figure
Open the dust bag compartment lid.
Remove the dust container and insert a dust bag.
Close the vacuum cleaner lid.
You have bought an extremely powerful device.
The highest suction setting is therefore only recommended
for heavily soiled, short-pile carpets and hard floors.
The required suction power can be selected by adjusting
the suction regulator (see Figure 9).
Low suction range:
For vacuuming delicate fabrics, e.g. curtains.
Middle suction range:
For daily vacuuming of lightly soiled floors.
High suction range:
For vacuuming durable floor coverings, hard floors and
for heavily soiled surfaces.

Changing the dust bag

Replacing the dust bag
31*
31
Figure
If the dust bag change indicator in the lid is filled
a)If the dust bag change indicator is completely yellow
completely when the floor tool is lifted from the
when the floor tool is lifted from the floor and the
floor with the highest suction level selected, the
highest suction power is selected, the dust bag must
dust bag must be changed, even though it may not
be changed. In this case it is essential to change the
yet be full. Even if the dust bag is not full, it may
dust bag due to the type of material it contains.
still need changing, due to the type of dust which
The nozzle, suction pipe and flexible tube
has been vacuumed. First check that the nozzle,
must not be blocked, as this would also
suction pipe and flexible hose are not blocked, as
cause the dust bag change indicator to be
this would also lead to the dust bag change indica-
triggered.
tor being triggered.
* Depending on model
51