Chicco Go-One Mode D'emploi page 28

justment pushbutton. Simultaneously, take
hold of the two child car seat straps below the
shoulder pads and pull them towards you in
order to loosen them (Fig. 16).
- Open buckle (G) on the child car seat belt, press
on the red pushbutton (Fig. 17) and widen
the straps outwards. Once done, baby can be
seated into the car seat (Fig. 18).
WARNING! Always check to make sure that the
child' back adheres correctly to the backrest (Fig.
19).
- Position the padded central lap harness cor-
rectly, take hold of the straps, overlap the two
buckle tabs (Fig. 20-21) and push them very
firmly inside the buckle housing so that there
is a clearly audible "click" (Fig. 22).
For optimised safety, the two buckle tabs have
been designed so that it is impossible to lock in
only one of them at a time.
ADJUSTING THE HEADREST HEIGHT AND
HARNESS STRAPS
Restraint harness straps and headrest height can
be adjusted simultaneously to 6 different posi-
tions, by acting on the rear adjustment pushbut-
ton (L).
WARNING! For correct adjustment, check that the
headrest is positioned so that the shoulder straps
exit the backrest at the same height as the child's
shoulder level (Fig. 23). To set the adjustment
height, keep the adjustment pushbutton that is
located to the rear of the backrest pressed in (Fig.
24), and, simultaneously slide the headrest until
it reaches the required position (Fig. 25). Once
done, release the pushbutton and guide the
headrest further in until there is the "click" con-
firming lock-in.
For correct child car seat harness straps tension-
ing, pull on the harness adjustment strap (Fig.
26) until the straps and belts fit perfectly to the
child's body.
Once the straps and belts have been adjusted,
take hold of the shoulder straps and pull down-
wards.
WARNING! The strap must be accurately and well
tensioned, adhering to the child's body without
being too tight: at shoulder level, it must be pos-
sible to fit a finger in between the child's shoulder
and the harness strap.
WARNING! Check that the straps/belts are not
twisted anywhere along the strap/belt length. In
particular, check at child's abdomen.
ADJUSTING THE BACKREST INCLINATION.
The backrest can be reclined to 5 positions.
To change backrest inclination, it is necessary to
pull the lever located under the child car seat
firmly forward towards you (Fig. 27).
WARNING! Once the required backrest inclination
has been set, first release the lever then continue
moving the seat until there is an audible click con-
firming lever lock-in.
WARNING! Once the required backrest inclination
has been set, always check to make sure that the
overall child car seat straps and belt are correctly
tensioned.
WARNING! During the adjustment operations,
check to make sure that none of mobile parts
come into contact with the child or other children
also travelling in the vehicle.
MAINTENANCE
The cleaning and maintenance operations must
only be carried out by an adult.
How to Clean the Fabric cover
The child car seat's fabric cover can be entirely
removed and either hand washed or machine
washed at 30°C. Please check the care label for
correct instructions on cleaning the seat fabric
cover.
Machine washable at 30°
Do not bleach
Do not spin dry
Do not iron
Do not dry clean
Never use abrasive detergents or solvents. Do not
spin or tumble the fabric cover, simply leave it to
dry without wringing. The cover is an integral part
of the child car seat and therefore, subject to safe-
ty regulations, the fabric cover can be replaced
only with another original fabric cover approved
by the manufacturer.
WARNING! To prevent individual safety hazards,
strictly never use the child car seat without its
fabric cover.
To remove the fabric cover, first release the re-
straint harness as follows:
- press the restrain harnesses adjustment button
and, at the same time, grasp the two child car
seat straps below the shoulder straps, pulling
28