Festool CTM 44 E Notice D'utilisation D'origine page 14

3.6 Connecting pneumatic tools
Make sure that the pneumatic tool is
switched off when plugging it in and un-
plugging it.
When the compressed-air module (1.8) (452829;
supplied ready with CTM 44 LE) is fi tted, the au-
tomatic cut-in of the appliance also operates in
conjunction with compressed-air tools. We also
recommend fi tting of the VE supply unit (452797).
The supply unit fi lters and oils the compressed
air and allows the air pressure to be regulated.
An IAS connecting piece (454757) is available for
connecting Festool compressed-air tools with the
IAS system. To ensure trouble-free functioning of
the automatic cut-in, the operating pressure of
the tool must be 6 bar.
4 Operation
4.1 Opening/closing the vacuum cleaner
- Open retaining clamps (2.2),
- Raise upper part (2.4) until support catch (2.5)
engages.
Follow the reverse order to close the appliance.
You must raise the upper part slightly before de-
pressing or disengaging the support.
4.2 Changing the fi lter
During the following procedure, take care
not to raise dust more than is unavoid-
able.
Wear a P2 breathing protection mask with
health-hazardous dusts!
a) Changing the fi lter bag (3.4)
Order no.:
CTM 44 E/CTM 44 LE
CTM 55 E
- Open the vacuum cleaner,
- Remove the used fi lter bag (see printed text on
fi lter bag),
- Dispose of the used fi lter bag in accordance with
statutory requirements,
- Thoroughly clean the dirt container (2.10) and
the space (3.1) for suction turbine (wipe down
with a damp cloth),
- Insert new fi lter bag (see printed text on fi lter
bag). Important: Press the fi lter bag sleeve (3.3)
fi rmly onto the dust extraction fi tting (3.2)!
- Close the vacuum cleaner.
b) Changing the fi lter element (2.3)
Order no.:
Do not operate machine without a fi lter
element. This may damage the motor.
- Open the vacuum cleaner,
- Remove the used fi lter element (see printed text
on the fi lter element packaging),
- Dispose of the used fi lter element in a sealed,
dust-tight bag in accordance with statutory re-
quirements,
- Thoroughly clean dirt container (2.10) and space
(3.1) for the suction turbine (wipe down with a
damp cloth),
- Fit a new fi lter element (see printed text on the
fi lter element packaging),
- Close vacuum cleaner.
4.3 Cleaning the fi lter element
To clean, move the handle (2.1) to and fro about
10 times. N.B.: You need to clean the fi lter ele-
ment only if you use the vacuum cleaner without
a fi lter bag.
4.4 Emptying the dirt trap (2.10)
Always remove the upper part of the vacuum
cleaner before emptying the dirt container!
- Open the vacuum cleaner,
- Raise the upper part slightly, depress the sup-
port (2.5),
- Raise the upper part to the stop (vertical posi-
tion),
- Remove the upper part by moving it forwards
horizontally,
- Empty the dirt container,
- Replace the upper part. Warning: Make sure
that both upper-part pins are fully inserted in
the recesses (1.5)!
- Close the vacuum cleaner.
452972
452973 4.5 Stand/Brake
The wheels can be blocked by the brakes (2.8),
thus preventing the vacuum cleaner from rolling
away unexpectedly.
4.6 Hose depot (partly in scope of delivery)
Securing the hose depot on the dust extractor:
see Fig. 4. When work is complete, you can guide
the extractor hose through the opening (4.1) and
deposit the hose in the depot. Similarly, the mains
cable can also be guided through the opening (4.2)
and deposited in the hose depot.
452923
14