Hama 00118489 Mode D'emploi page 4

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 6
G Operating instruction
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please
keep these instructions in a safe place for future reference. If you sell the device, please
pass these operating instructions on to the new owner.
1. Explanation of warning symbols and notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific
hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package contents
• Monitor Arm
• Mounting kit (see Fig. 1 for contents)
• These operating instructions
Note
Please check the mounting kit for completeness before installing the product and
ensure that there are no faulty or damaged parts.
3. Safety instructions
Warning
• Given the multitude of terminal devices available on the market, the supplied
mounting kit is unable to cover every option.
• The screws for attaching the terminal device to the product may occasionally be
too long.
• Read the operating instructions for your terminal device before attempting to
mount it. The instructions provide information about the type and measurements
of suitable fastening materials.
• If the supplied mounting kit does not contain suitable fastening materials for
mounting the terminal device, purchase these from a specialised dealer.
• Never apply force during installation. This can damage your device or the product.
• If in doubt, have this product mounted by a qualified technician - do not attempt
to mount it yourself!
• Once you have mounted the product and the attached load, check that they are
sufficiently secure and safe to use.
• You should repeat this check at regular intervals (at least every three months).
• Ensure that the product does not exceed its maximum permitted carrying capacity
and that no load exceeding the maximum permitted dimensions is attached.
• Make sure that the product is loaded symmetrically.
• During adjustment, ensure that the product is loaded symmetrically and that the
maximum permitted carrying capacity is not exceeded.
• In the event of damage to the product, remove the attached load and stop using
the product.
• Mount the product only on tabletops with a sufficient load-bearing capacity and
stability for the product and the device attached to it.
• Ensure that the thickness of the tabletop is 3-8.5 cm.
• Do not attach any additional objects to the product.
• Keep the packaging material out of the reach of children due to the risk of
suffocation.
• Dispose of packaging material immediately in accordance with the locally applicable
regulations.
• Note that the product can cause pressure marks on the surface of the table. This
depends on the weight loading and on the stability of the surface at the place of
installation.
4. Application and specifications
• The product is used for mounting flat screens in private households.
• The product is intended only for use inside buildings.
• Use the product only for the intended purpose.
2
Maximum load:
10 kg
Screen diagonal:
33 – 81 cm (13"– 32")
Rotation:
360°
Tilt:
-/+ 45° (device-dependent)
Swivel range:
up to 180° on 2 joints (device-dependent)
Holder:
up to 100 x 100, according to VESA standards
5. Preparation and installation
Note
• The product must be mounted by two people. Seek assistance and help!
• Different end devices have different connections for cabling and other devices.
Before commencing the installation, check whether the necessary connections
can still be reached after mounting.
• Depending on the product and mounting method, you may not need all parts of
the mounting kit. It is therefore possible that unneeded screws and other small
parts will be left over even after correct mounting. Keep these in a safe place
together with the instructions for use for later reference (sale of the product,
moving house).
• Observe the other warnings and safety instructions.
• Proceed step-for-step in accordance with the illustrated installation instructions.
(Fig. 1a et seq.).
Note
• Given the multitude of terminal devices structures available on the market, we
cannot describe all possible mounting options here.
• Please ensure that the bracket lays flat and evenly on the back of the monitor.
• Ensure that all screws have the proper length and can be mounted until they are
hand-tight (see Fig. 3).
6. Adjustment & maintenance
Note – Height adjustment
• The bracket must be adjusted by two people! Seek assistance and help!
• During adjustment, ensure that the product is loaded symmetrically and that the
maximum permitted carrying capacity is not exceeded.
Note – Setting/adjusting the tilt angle
• To permanently set the tilt angle, loosen the fastening screws at the side, set the
desired tilt angle and then tighten the screws again (see Fig. 4).
• In order to be able to flexibly adjust the tilt angle, turn the screws hand-tight only.
In this way, the screen can be adjusted at any time.
• No screws need to be loosened for the sideways movement.
• Once you have mounted the product and the attached load, check that they are
sufficiently secure and safe to use.
• You should repeat this check at regular intervals (at least every three months).
• Only clean this product with a slightly damp, lint-free cloth and do not use aggressive
cleaning agents.
7. Warranty disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage
resulting from improper installation/mounting, improper use of the product or from
failure to observe the operating instructions and/or safety notes.

Publicité

Table des Matières
loading

Table des Matières