General Safety Rules - Homelite 26CS UT33600 Manuel D'utilisation

WARNINg:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
READ ALL INSTRUCTIONS
 For safe operation, read and understand all instructions
before using this product. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
 Do not allow children or untrained individuals to use this
unit.
 Do not start or operate the engine in a confined space,
building, near open windows, or in other unventilated
space where dangerous carbon monoxide fumes can
collect. Carbon monoxide, a colorless, odorless, and
extremely dangerous gas, can cause unconsciousness
or death.
 Clear the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the cutting line
or blade.
 Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
 Wear heavy, long pants, long sleeves, boots, and gloves.
Do not wear loose fitting clothing, short pants, sandals,
or go barefoot. Do not wear jewelry of any kind.
 Product users on United States Forest Service land, and
in some states, must comply with fire prevention regula-
tions. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
your federal, state, or local authorities.
 Never operate this unit on the operator's left side.
 Secure long hair above shoulder level to prevent entangle-
ment in moving parts.
 Keep all bystanders, children, and pets at least 50 ft. away.
Bystanders should be encouraged to wear eye protection.
 Do not operate this unit when you are tired, ill, upset, or
under the influence of alcohol, drugs, or medication.
 Do not operate in poor lighting.
 Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces. Keep cutting attachment below waist.

gENERAL SAFETY RULES

Page 3 — English
 To avoid hot surfaces, never operate the unit with the
bottom of the engine above waist level.
 Keep all parts of your body away from any moving part.
 Do not touch area around the muffler or cylinder of the
unit; these parts get hot from operation.
 Always stop the engine and remove the spark plug wire
before making any adjustments or repairs except for
carburetor adjustments.
 Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace any damaged parts before use.
 The string head will rotate during carburetor adjustments.
 It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. It is presently unknown what, if any, vibrations
or extent of exposure may contribute to the condition.
There are measures that can be taken by the operator to
possibly reduce the effects of vibration:
a) Keep your body warm in cold weather. When operating
the unit wear gloves to keep your hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
b) After each period of operation, exercise to
increase blood circulation.
c) Take frequent work breaks. Limit the amount of
exposure per day.
d) Keep the product well maintained, fasteners
tightened and worn parts replaced.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician about
these symptoms.
 Mix and store fuel in a container approved for gasoline.
Do not smoke while fueling or mixing fuel.
 Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 30 ft. away from refueling
site before starting engine.
 Stop the engine and allow to cool before refueling or
storing the unit.
 Allow the engine to cool; empty the fuel tank into a con-
tainer approved for gasoline and secure the unit from
moving before transporting in a vehicle.
 Wear your protective equipment and observe all safety
instructions. Be sure the cutting attachment stops turning
when the engine idles. When the unit is turned off make
sure the cutting attachment has stopped before the unit
is set down.