Starting Operation - Bosch GAS 18V-10 L Professional Notice Originale

18 | English
Changing the Battery Compartment Cover
(see figures A3−A5)
If you wish to use a ProCORE18V 12Ah battery, the battery
compartment cover (12) can then no longer be closed. In
this case, the battery compartment cover (12) can be re-
placed with a screen (23) designed for this purpose.
In damp or wet conditions, the dust extractor may only be
used with the battery compartment cover closed.
Removing the Battery Compartment Cover
(see figure A3)
Remove the battery (20) from the battery bay (19).
Remove the two fastening screws (22) (ST4×12) with a
cross-headed screwdriver PH1 and take off the battery com-
partment cover (12).
Inserting the Screen (see figure A4)
Press the battery compartment cover bracket (24) down-
wards and slide on the screen (23).
Removing the Screen (see figure A5)
Apply a slot screwdriver, push the screen (23) a little way to-
wards the rear and remove the screen. When doing so, press
the battery compartment cover bracket (24) downwards.
Fitting the Brackets for Extractor Accessories
(see figure B)
– Slide the bracket (25) for the suction tube and crevice
nozzle firmly into the adapter (10) provided for it from
above until it clicks into place.
– Slide the bracket (27) for the vacuum hose and floor
nozzle firmly into the adapter (7) provided for it from
above and tighten the fixing bolts (26).
Fitting the vacuum hose (see figure C)
– Insert the vacuum hose (13) into the hose adapter (8) un-
til both snap fasteners (28) of the vacuum hose click into
place.
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state).
Fitting the Vacuuming Accessories
The vacuum hose (13) is equipped with a clip system which
can be used to connect vacuuming accessories (dust extrac-
tion adapter (14), curved nozzle (15)).
Fitting the extraction adapter or curved nozzle
(see figure D)
– Fit the extraction adapter (14) or the curved nozzle (15)
to the vacuum hose (13) until the two snap
fasteners (28) on the vacuum hose audibly click into
place.
– To remove the adapter, press the snap fasteners (28) in-
wards and pull apart the components.
1 609 92A 7MV | (12.05.2022)
Fitting the Nozzles and Tubes
– If required, place the suction tubes (18) firmly inside one
another and then attach them firmly to the curved nozzle
(15).
– Attach the floor nozzle (17) or the crevice nozzle (16)
firmly to the suction tube (18) or the curved nozzle (15).
Attaching the carrying strap (see figure E)
The carrying strap is only intended for carrying and at-
u
taching the dust extractor and not as a safety harness.
Click the snap hooks of the carrying strap (29) into the
fastening eyes (9) of the dust extractor.
Fitting the Rollers (see figure F)
Insert the 4 fastening pins on the rollers (30) into the roller
adapters (31) until they audibly click into place.
Other rollers can also be used as per the EN 12529 standard
(11 mm fastening pin diameter).
Check the functionality of the roller brakes before us-
u
ing the dust extractor.
Operation
Remove the battery before cleaning or performing
u
maintenance on the dust extractor, making tool ad-
justments, changing accessories or placing the dust
extractor in storage. This safety measure prevents the
dust extractor from being started accidentally.
Ensure that the work area is clean and tidy to minim-
u
ise the risk of tripping.

Starting Operation

The dust extractor must not be used without a filter.
u
Do not use damaged filters (e.g. no cracks, small
u
holes, etc.). Replace any damaged filters immedi-
ately.
Before extraction, ensure that the filter unit is se-
u
curely fitted.
Before extraction, ensure that the battery compart-
u
ment cover is securely closed.
Please inform yourself about the applicable regula-
u
tions/laws on how to handle harmful types of dust in
your country.
Only vacuum rock dust with the power tool and dust
u
extraction system combination explicitly identified,
for which it has been proven that the legal thresholds
are not exceeded. You can find this evidence at
http://www.bosch-professional.com/dust.
The dust extractor must categorically not be used in poten-
tially explosive areas.
To ensure optimum suction power, you must always fully un-
wind the vacuum hose (13) from the vacuum hose
bracket (27).
Bosch Power Tools