Pioneer DJM-850-K Mode D'emploi page 22

Category
EFFECT
SELECT
BEAT EFFECTS
CH
SELECT
TIME
LEVEL/DEPTH
ON/OFF
!
ON/OFF
!
HI
MIC
LOW
NOISE
GATE
SOUND COLOR FX
CRUSH
FILTER
FADER START 1
FADER START 2
Fader Start
FADER START 3
FADER START 4
MIXING
HEADPHONES
LEVEL
Timing Clock
FADER START 1
FADER START 2
Fader Start
FADER START 3
FADER START 4
START
MIDI
STOP
1 When turning one button on switches another button from on to off, MIDI on and off messages are sent from the two buttons.
When there is no button that switches off, only the MIDI on message is sent from the button that was pressed.
2 When switched from one position to another position, the MIDI ON and OFF signals are sent respectively from both positions.
! When the [START/STOP] button is pressed for over 1 second, MIDI messages corresponding to the positions of the buttons, faders and controls are sent in a bundle
(Snapshot).
The MIDI Snapshot sends all MIDI messages other than MIDI start and MIDI stop.
22
En
SW Name SW Type
DELAY Switch
Switch
ECHO
UP ECHO Switch
SPIRAL Switch
REVERB Switch
TRANS Switch
FILTER Switch
FLANGER Switch
PHASER Switch
ROBOT Switch
SLIP ROLL Switch
Switch
ROLL
REV ROLL Switch
SND/RTN Switch
Switch
CH1
CH2 Switch
CH3 Switch
Switch
CH4
MIC Switch
CF.A Switch
Switch
CF.B
MASTER Switch
Switch
Switch
Switch
When an effect
other than [SND/ Button
RTN] is selected at
BEAT EFFECT
When [SND/RTN]
Button
is selected at BEAT
EFFECT
Control
Control
Button
Button
Button
Button
Button
Button
Button
Button
Control
Control
—
Button
Button
MIDI assignment Trigger/Toggle
CC 042
2
CC 055
2
CC 061
2
CC 043
2
CC 054
2
CC 053
2
CC 059
2
CC 050
2
CC 057
2
CC 051
2
CC 058
2
CC 046
2
CC 047
2
CC 062
2
CC 034
2
CC 035
2
CC 036
2
CC 037
2
CC 038
2
CC 039
2
CC 040
2
CC 041
2
CC 013 —
CC 045 —
CC 091 —
CC 114 —
CC 064 —
CC 030 —
CC 031 —
CC 085 Trigger/Toggle
CC 105 Trigger/Toggle
CC 086 Trigger/Toggle
CC 087 Trigger/Toggle
CC 088 Trigger/Toggle
CC 089 Trigger/Toggle
CC 090 Trigger/Toggle
CC 093 Trigger/Toggle
CC 027 —
CC 026 —
Timing Clock —
Note 102 —
Note 103 —
Note 104 —
Note 105 —
START —
STOP —
Transmitted data
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
—
TIME value (When FLANGER, PHASER
or FILTER is selected, the value is halved.
When a negative value is selected, it is set
to a positive value.)
0-127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
1
OFF=0, ON=127
1
OFF=0, ON=127
1
OFF=0, ON=127
1
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
—
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
—
—