Pioneer DJM-850-K Mode D'emploi page 19

SPIRAL
1 2
This function adds a reverberation effect to the input sound.
When the delay time is changed, the pitch changes simultaneously.
Input sound turned off
1 beat
BEAT c, d buttons Use these to set a time delay of 1/8 – 16/1 with
(parameter 1) respect to the time of one beat of the BPM.
Use this to set the delay time.
TIME control (parameter 2)
10 to 4000 (ms)
Use this to set the balance between the original
LEVEL/DEPTH control
sound and the effect sound and to set the quantita-
(parameter 3)
tive parameter.
REVERB
1 2
This function adds a reverberation effect to the input sound.
Direct sound
Early reflected sound
Level
Reverberations
1%
100%
Use these to set the extent of the reverberation
BEAT c, d buttons
(parameter 1) effect, from 1 – 100 %.
Use this to set the degree of the reverb effect.
TIME control (parameter 2)
1 – 100 (%)
Use this to set the balance between the original
LEVEL/DEPTH control sound and the effect sound and to set the cut-off
(parameter 3) frequency of the filter through which the effect
sound passes.
TRANS
1
The sound is cut according to the beat fraction set with the [BEAT c, d]
buttons.
Cut
1/1 beat
BEAT c, d buttons Use these to set a cut time of 1/16 – 16/1 with
(parameter 1) respect to the time of one beat of the BPM.
Use this to set the effect time.
TIME control (parameter 2)
10 to 16000 (ms)
LEVEL/DEPTH control Sets the balance between the original sound and the
(parameter 3) effect sound.
FILTER
1
The filter's cutoff frequency changes according to the beat fraction set
with the [BEAT c, d] buttons.
Fade-out
Time
Time
Cut
Time
Frequency
Use these to set the cycle for moving the cut-off
BEAT c, d buttons
frequency as a time of 1/4 – 64/1 with respect to the
(parameter 1)
time of one beat of the BPM.
Use this to set the cycle at which the cut-off fre-
TIME control (parameter 2) quency is moved.
10 to 32000 (ms)
LEVEL/DEPTH control The further the control is turned clockwise, the more
(parameter 3) the effect is stressed.
FLANGER
1
A 1-cycle flanger effect is produced according to the beat fraction set
with the [BEAT c, d] buttons.
Short delay
Cycle
BEAT c, d buttons Use these to set the 1/4 – 64/1 effect time with
(parameter 1) respect to the time of one beat of the BPM.
Use this to set the cycle by which the flanger effect
TIME control (parameter 2) moves.
10 to 32000 (ms)
The further the control is turned clockwise, the more
LEVEL/DEPTH control the effect is stressed.
(parameter 3) When turned all the way counterclockwise, only the
original sound is output.
PHASER
1
The phaser effect changes according to the beat fraction set with the
[BEAT c, d] buttons.
Phase shift
Cycle
Use these to set the cycle for moving the phaser
BEAT c, d buttons
effect as of time of 1/4 – 64/1 with respect to the
(parameter 1)
time of one beat of the BPM.
This sets the cycle by which the phaser effect is
TIME control (parameter 2) moved.
10 to 32000 (ms)
The further the control is turned clockwise, the more
LEVEL/DEPTH control the effect is stressed.
(parameter 3) When turned all the way counterclockwise, only the
original sound is output.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
BEAT c, d buttons Use these to set the degree of the effect sound, from
(parameter 1) -100 – 100 %.
Use this to set the degree of the effect sound.
TIME control (parameter 2)
-100–100 (%)
LEVEL/DEPTH control Sets the balance between the original sound and the
(parameter 3) effect sound.
Time
Time
19
En