Pioneer DJM-850-K Mode D'emploi page 17

 Using the external effector
1 Connect this unit and external effector.
For instructions on connections, see Connecting output terminals on
page 7.
2 Turn the [DELAY, ECHO, UP ECHO, SPIRAL, REVERB,
TRANS, FILTER, FLANGER, PHASER, ROBOT, SLIP ROLL,
ROLL, REV ROLL, SND/RTN] selector switch.
Select [SND/RTN].
3 Turn the [1, 2, 3, 4, MIC, CF.A, CF.B, MASTER] selector
switch.
This selects the channel to which the effect is applied.
4 Press the [ON/OFF] button for [BEAT EFFECTS].
The sound that has passed through the external effector is output from
the [MASTER] channel.
! When the [ON/OFF] button is pressed again, the effect turns off.
Operating DJ software using the MIDI
function
This unit is equipped with a "Full Assignable MIDI" function allowing the
operation information of virtually all of the unit's controls and buttons
to be sent to the DJ software as MIDI signals. This unit can be used as a
USB MIDI controller when it is connected by USB cable to a computer
on which MIDI-compatible DJ software is installed. Furthermore, the
tempo (BPM) of the sound being played is sent as MIDI timing clocks, so
the tempo on the DJ software can be synchronized with the tempo of the
sound output from this unit.
To operate DJ software with this unit, first install the MIDI-compatible DJ
software on the computer. The MIDI-related settings must also be made
on the DJ software.
! For the messages output by this unit, see List of MIDI Messages on
page 21.
! If you want to change this unit's MIDI channel, see Changing the
settings on page 23.
1 Connect this unit's [USB] terminal to the computer.
For details about connections, see Connecting to the control panel on
page 8.
2 Launch the DJ software.
3 Press the [MIDI] [ON/OFF] button.
Turn the MIDI function on.
Transmission of the MIDI messages begin.
! When a fader or control is moved, a message corresponding to the
position is sent.
! When the [START/STOP] button is pressed and held in for more than
2 seconds, a set of MIDI messages corresponding to the button,
fader or control positions is sent (Snapshot).
! When the [ON/OFF] button for [MIDI] is pressed again, transmission
of MIDI messages stops.
! The MIDI timing clocks (BPM information) are sent regardless of the
[MIDI] [ON/OFF] button's setting.
 Sending the MIDI start and MIDI stop messages
Press the [START/STOP] button for [MIDI].
! The MIDI start and MIDI stop messages are sent alternatively each
time the [START/STOP] button is pressed, regardless of whether the
MIDI function is on or off.
Operating an external MIDI sequencer
This unit is equipped with a "Full Assignable MIDI" function allowing
the operation information of virtually all of the unit's controls and but-
tons to be sent to an external device (effector, etc.) as MIDI signals. This
unit can be used as a USB MIDI controller when it is connected by MIDI
cable to a MIDI-compatible external device. Furthermore, the tempo
(BPM) of the sound being played is sent as MIDI timing clocks, so the
tempo on the external device (sequencer, etc.) can be synchronized with
the tempo of sound output from this unit.
! For the messages output by this unit, see List of MIDI Messages on
page 21.
! External MIDI sequencers not supporting MIDI timing clocks cannot
be synchronized.
! External MIDI sequencers cannot be synchronized for sources for
which the BPM cannot be measured stably.
! The MIDI timing clock is output even with BPM values input manu-
ally by tapping the [TAP] button with a finger. The MIDI timing clock
output range is 40 BPM to 250 BPM.
1 Connect the [MIDI OUT] terminal to the external
MIDI sequencer's MIDI IN terminal using a commercially
available MIDI cable.
2 Set the external MIDI sequencer's sync mode to Slave.
3 Press the [START/STOP] button for [MIDI].
The MIDI start message is sent.
4 Press the [MIDI] [ON/OFF] button.
Transmission of the MIDI messages begin.
17
En