TWIST be cool Instructions page 34

GB
the size of the child at proper position for
child's head.
-Check that the shoulder pad should be lo-
cated slightly above the child's shoulder. The
shoulder harness should lie in the middle
between the child's neck and the outer edge
of the shoulder.
4 REMOVING THE TWIST
To make the removal of TWIST easier we
recommend you first remove the seat (A)
(See "Remove the Seat")
Always mount and remove the seat without
a child in it!
Push the release button to the central direc-
tion, and move the support leg into its top-
most position.
Rotate the isofix sytem control dial on the
fron t of TWIST base to anti-clock wise direc-
tion to move the Isofix base forward.
Pull the Isofix system unlocking buttons on
both side of the base in forward direction, so
the Isofix connectors are released from the
vehicle's anchoring point.
Lift the TWIST out of the vehicle's seat.
5 USING THE RECLINING ADJUSTMENT
Pull the reclining handle underneath of front
seat forward, release the handle at your re-
quired position until you hear a "CLICK" to
make sure it's locked.
6 REMOVING/ATTACHING THE COVER
To remove the cover, the seat shell (A) has
to be removed from the base (B) first. (SEE
"Remove the seat")
1. Loose the harness system by adjusting the
central device.
2. Unlock the harness buckle, then take off
the Pelvic Insert for new born to 13kg.
3. First remove the cover from the headrest.
4. Use a pencil-like tool to push the elastic
bands buttons from top to downwards direc-
tion, and take off the bands which attached
to two buttons on both side on the seat shell.
5. Thread the main buckle body through the
buckle pad and out underneath the cover
6. Loose the elastic bands which are located
in the placed marked red on the reverse side
of the cover, and pull the seat off in forward
direction to take off the main cover.
Check that all the locks are closed and all
34
anchoring are correctly fastened.
7 REMOVING THE PELVIC INSERT
If the child's bodyweight exceeds 9kg, the
pre-mounted pelvic insert should be removed.
CARE INSTRUCTIONS
Light dirt can be easily removed with a damp
cloth. The cover can also be removed and
washed at 30ºC. Remove the back cushion
from the cover of the head support before y
ou wash it.
The cover material color may run slightly when
wet, in particular during washing.
Do not use solvents on the cover!
WARRANTY CONDITIONS
The warranty period begins at the time of purchase.
The warranty period granted in compliant with the
legal warranty period in the country of purchase. In
terms of content, the warranty covers rework, re-
placement delivery, or a rebate as the manufacturer
sees fit.
The warranty applies only for the original user. In
case of a fault, warranty rights will be applicable
only if the dealer, where the item was purchased is
notified immediately after initial detection. Should
the dealer be unable to remedy the issue, then the
product will be returned to the manufacturer with
a detailed description of the fault, and with the of-
ficial purchase document including the date of pur-
chase.
The manufacturer shall not accept liability for
faulty products not delivered by him.
Warranty claims are not valid if:
·the product was modified.
·the product is not returned complete and accom-
panied by the original purchase document to dealer
within 14 days of the detection of the fault.
·the fault occurred due to inappropriate handing
or maintenance, or due to other actions that are
the fault of the user, specifically where the user in-
structions were not complied with.
·repairs on the product were carried out by third
parties.
·the defect was caused by an accident.
·the serial number has been damaged or removed.
Modifications to or deterioration of the product
caused by the contractually agreed use of the item
(normal wear and tear) will not be accepted as a
warranty claim.
Any services rendered by the manufacturer in case
of a warranty claim shall not extend the warranty
period.