TWIST be cool Instructions page 33

GB
see the Safety display shows GREEN on the
top front side of Isofix base.
Rotate the Isofix system control dial to the
Clockwise direction until the seat close as
possible to the back rest of the vehicle's seat,
make sure the gap has eliminated.
Adjusting the Support Leg.
Push the release buttons on both side to the
center direction, and extending the support
leg to the surface of floor until it fully reaches,
make sure you see the safety display shows
GREEN on both side.
CAUTION!
• The seat must be secured with the Isofix sys-
tem even if there is no child is travelling.
• Both Isofix connectors must be anchored se-
curely and safety displays are all show GREEN.
• The seat shell are fully locked on the Isofix
base and safety displays are all show GREEN.
• The support leg must fully reaches surface
of floor and the safety displays are all show
GREEN.
Step 2.2 Locking the seat to the Isofix base in
FORWARD POSITION: 9 to 18kg.
a) Lifting the seat, lock the metal tube in the
underneath of the rear side of the shell to lock
into the REAR-LOCK on Isofix base.
b) Pull the LOCKING-HANDLE forward, and
push the front edge of the shell downwards,
and lock the metal tube in the underneath of
the front side of the shell to lock into FRONT-
LOCK on Isofix base.
c) Release the LOCKING-HANDLE, and lock
the metal tube in the front side, make sure you
see the Safety display shows GREEN on the
top front side of Isofix base.
CAUTION!
• Make sure that the seat is correctly anchored
to both anchoring points and the safety dis-
play shows GREEN.
• If the child's body weight exceeds 9kg, the
pre-installed pelvis insert should be removed.
(See "Removing the Pelvis Insert").
• Always mount the seat without a child in it.
Rotate the Isofix system control dial to the
Clockwise direction until the seat close as
possible to the back rest of the vehicle's seat,
make sure the gap has eliminated.
Adjusting the Support Leg.
Push the release buttons on both side to the
center direction, and extending the support
leg to the surface of floor until it fully reaches,
make sure you see the safety display shows
GREEN on both side.
CAUTION!
• The seat must be secured with the Isofix sys-
tem even if there is no child is travelling.
• Both Isofix connectors must be anchored
securely and safety displays are all show
GREEN.
• The seat shell are fully locked on the Isofix
base and safety displays are all show GREEN.
• The support leg must fully reaches surface
of floor and the safety displays are all show
GREEN.
3 SECURING YOUR CHILD IN THE TWIST
CAUTION!
Check that the TWIST is mounted properly
and that all belts have proper tension, also
that all locking mechanisms are secured and
all safety displays show GREEN.
Adjusting the central device
At the front of the seat under the cover there
is the central adjusting device, which clamps
the central harness tight. Loosen the central
adjusting device by pushing the cap of the
central adjusting device up and pull the har-
ness forward (do not pull on the harness cushion).
Adjusting the headrest.
Close the both side of the headrest to the
central direction, at the same time, lifting
up or pushing down the headrest at your
required position.
Placing your child in the seat.
- Open the harness buckle by pushing the red
button, and parting the buckle tongue to the
sides.
- Place your child as far back into the seat as
possible, bring the shoulder/lap harness and
central harness in the front of the child and
match the tongue first, then insert into main
body of the buckle.
- Pull the central harness on the adjusting de-
vice to make sure the harness secures your
child at proper tightness, by checking with
your two fingers gap between harness and
your child's front shoulder point. Make sure
your child is comfortable and secured.
Checking Point.
-Check that the buckle is fully closed, and
none of the harness straps are twisted.
-Check that the headrest must be adjusted to
33