ExtraStove ES 11 Manuel D'installation page 19

screen, alternated to other displays, to indicate that the function is operating.
13) AUTO Function: Pressing the AUTO button on the remote control during the heating
8
10
11
13
phase, the stove modulates the heating power in proportion to the preset tempera-
ture. During the stove heating phase, the word "Auto" is displayed on the screen,
alternated to other displays, to indicate that the function is operating.
14) ECO Function: Pressing the ECO button on the remote control during the heating
phase, the stove lowers the heating power, every 10 minutes, until the minimum
power is reached. During the stove heating phase the word "Eco" is displayed on
the screen, alternated to other displays, to indicate that the function is operating.
ATTENTION!
functions by remote control TURBO - SLEEP - AUTO - ECO are active
only on some models.
Please remember that the first lighting must be performed by our
certified Authorized Assistance Centre (Law 37/2008) that verifies
the installation and completes the guarantee.
During the first lighting the environment should be well ventilated
since during the first hours of operation unpleasant odours could
develop due to the physical stabilizing of the paint and from the
grease in the tubyère wrapping.
2.1 Suggestions
Do not continuously turn the stove on and off as this could provoke sparks that could
shorten the life of the electrical components.
• Do not touch the stove with wet hands: the stove has electrical components that could
produce sparks if handled incorrectly. Only authorized technicians can resolve possible
problems.
• Do not remove any screws from the fire chamber without first lubricating them well.
• Never open the glass door of the pellet stove while the stove is in operation.
• Be sure that the brazier basket is positioned correctly.
• The flue system must be suitable for inspecion. If it cannot be removed, it must have
some holes for inspection and cleaning.
2.2 How to load pellets in the tank
You can load pellets in the tank through the door on the upper part of the stove.
Join the following procedure to load pellets:
• Open the door on the upper part of the stove;
• Load the wished pellets quantity with caution (load enough pellets to grant a sufficient
functioning of the stove);
• Close the door.
3.0 Lighting the stove
• Fill the container 3/4 full with the pellets recommended by the manufacturer;
• Connect the stove to an electrical outlet with the cable that has been supplied;
• Press the lighting switch located on the back part of the stove;
3.1 First start
Once powered the board, on the LCD display is displayed the version of the resident
software, further the status of the stove, that, in the case of first start, will be turned off.
3.2 Language Selection
The menu lets you choose the language of the messages from the panel:
• Italian
• English
• French
• German
• Spanish
• Greek
• Dutch
Using the "PROG +" and "PROG-" you can scroll through and select the desired lan-
guage.
3.3 Setting temperature
The desired room temperature is set using the keys + Temp and Temp-panel. The values
are settable from 10 to 40 ° C for air.
3.4 Setting the Program Operating
The program of operation is the heating power of the stove. The program can be set via
9
the PROG + and PROG-ranging from 1, lowest power, to 5, maximum power.
3.5 Turning on the stove
To turn on the stove it is necessary to press, for a few seconds, the ON/OFF button. The
stove will proceed automatically in the ignition phase and heating. If it is the first switch
on, meaning first load of pellets, it will be necessary to run multiple switching cycles in
12
such a way that the pellet enters the power supply circuit. Even in the case of re-ignition,
after the automatic shut down for finished pellet (Error Code 5), an ignition error could
14
occur due to the emptying of the supply circuit of the pellets. If the stove has not done
proper ignition, the next time will still be reduced to the amount of pellets, depending
on the setting of the power during the switch on phase, adjustable from 1 to 5. If the
ignition is still in the cooling phase of the stove switches to standby mode as long as
the flue gas temperature will not be dropped below the temperature of the stove off.
3.6 Turning off the stove
To turn off the stove simply press the "ON/OFF" button, when the LCD display is lit. The
system, using a controlled cooling, brings the stove on the OFF position.
3.7 Reset System Errors
The stove report, by error code, and comments, every anomalous situation detected.
Before re-ignition of the stove, be sure the stove is switched off and reset each error, by
pressing the "ON/OFF" button for about 3 seconds, however, until the disappearance of
the error message on the LCD. The last 10 faults are saved in a non-volatile memory
and can be viewed by entering the menu "LOG ERRORS". After each error code check
and empty the brazier. Then, in order to reactivate the stove, press simultaneously SET
and ON/OFF (3 sec).
In case appear the message "empty the brazier" simultaneously press SET and
ON / OFF for 3 seconds (to reset the alarm) and then the ON / OFF button to switch
the heater on again.
3.8 Heating Mode
You can change the heating mode at any time, by controlling both the program and the
temperature set using the keys available, and following the directions of the display and
of the panel itself. The stove automatically adjusts the power output in function of the
program and the ambient temperature detected by the probe.
3.9 Automatic or Manual Mode
The operation of the stove can be manual, on and off by the user, or automatic using
the built-in weekly programmer or timer to turn on or turn off the stove automatically at
set times to suit your needs. To change the mode, press the MOD key on the panel. The
display will indicate the selected mode at any time.
Manual mode:
The stove is controlled manually only and therefore every time you turn it on or off,
this is done through the "ON / OFF" key.
Automatic mode:
The stoves, in addition to being switched on and off manually, checks further the set-
tings in the timer and in the weekly programmer, switching on or off at the specified
hours or days set.
4.0 User Programming
The user programming is possible using a menu accessible by pressing the "SET" button
on the panel, when display is lit. To exit at any time from the menu without making any
changes, press the key "STOP". To view the status of the stove, at any moment, remind
that without pressing the keys of the panel for about 1 minute, the system will automa-
tically exit the menu. To scroll through the menu, use the "TEMP+" and "TEMP-"; to
enter the menu press "SET".
4.1 Adjust Date and Time
Pressing "SET", you enter the setup menu of built-in calendar. You can change the day
of the week from Monday to Sunday and the time and the date. To move among the va-
riables, use the "PROG+" and "PROG-", while to edit them using the "TEMP+" and
"TEMP-". To confirm the change, and exit, press the "SET".
19
WARNING!
Before lighting a small amount of smoke may fill the combustion
chamber.
WARNING!
it is necessary to daily clean the brazier and often clean the ash box.
The lack of cleanliness can prevent the starting of the stove, causing
damages to the stove itself and to the environment (possible emis-
sion of unbrunt material and soot).
Do not re-use the pellet possibly remained in the brazier due to no
starting-up.
G