Prior To Use; Checking For Gas Leaks - Campingaz DELANO CLASSIC Mode D'emploi

2) To use the equipment with the flexible hose XP D
36-112, G 1/2 and M 20x1.5 nuts: (solution d) b))
- loosen and remove the NF ringed tailpiece to release
GB
the G 1/2 inlet connector.
- remove the seal
- tighten the G 1/2 threaded nut on the hose onto the
barbecue inlet connector and the M20x1.5 threaded nut
onto the regulator output connector following the
instructions supplied with the flexible hose.
- use a spanner to tighten or loosen the threaded nut.
- use a spanner to hold the regulator outlet connector
firm.
- check for leaks following the instructions in paragraph f).
Check that the flexible hose stretches out normally
without twisting or pulling and does not come into contact
with the hot sides of the barbecue. It should be replaced
when the expiry date on the hose is reached or whenever
it is damaged or develops surface cracks.
Belgium, Luxembourg, Great Britain, Ireland,
Portugal, Spain, Italy, Croatia, Greece, Netherlands,
Czech Republic, Slovakia, Hungary, Slovenia,
Norway, Sweden, Denmark, Finland, Bulgaria,
Romania, Poland:
The barbecue is equipped with a circular connector. It
should be used with flexible hose that is suitable for use
with butane and propane gas. Hose length should not
exceed 1.20 metre. It should be replaced if it is damaged
or cracked, when required by national regulations or at the
end of the part lifecycle. Do not pull or pierce the hose.
Keep away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally,
without twisting or pulling.
Switzerland:
The barbecue must be used with flexible hose that is
suitable for use with butane and propane gas. Hose length
should not exceed 1.50 metre. It should be replaced if it is
damaged or cracked, when required by national
regulations or at the end of the part lifecycle. Do not pull
or pierce the tubing. Keep away from any parts of the
barbecue that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
Flexible hose connection: to connect the hose to the
connector on the barbecue, tighten the nut on the hose
firmly but without excess force using the two wrenches
provided:
- no. 14 wrench to tighten the connector
- no. 17 wrench to tighten the nut on the hose
e) LID
Handle the lid carefully, especially during operation. Do
not lean over the firebox.
f) CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knobs are in the "off" ( )
position.
3) Connect the flexible hose to the connector and
barbecue as described in part d).
4) Fit the regulator onto the gas cylinder in accordance
with its instructions.
5) Use a gas leak solution to test for leaks. Important:
never use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain
closed: off position ( )). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are
gas leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
barbecue must not be used until the leak has been
repaired.
9) Close the valve on the gas cylinder.
Important:
Check for leaks at least once per year and each time the
gas cylinder is replaced.
g) PRIOR TO USE
Never use the barbecue until the instructions have been
read carefully and understood. Also, be certain that:
- there are no leaks
- the venturi tubes are not blocked (example: spider
webs)
- the hose does not touch any components which may get hot.
- that the ventilation openings in the gas receptacle
housing are not obstructed, if appropriate.
h) LIGHTING THE BARBECUE BURNERS
Read steps 1 to 7 before beginning with step 1.
1) Open the lid.
2) Make sure that the control knobs are in the "OFF"
position ( ).
3) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip. Fit the regulator
onto the gas cylinder in accordance with its
instructions.
4) Open the gas cylinder valve.
5) Press one of the 2 control knobs and turn it to the
FULL FLAME ( ) position. Wait about 5 seconds, then
press the igniter button ( ) until you hear the click.
Repeat 3 or 4 times if necessary until the burner is lit.
10