Important; Operating Your Dehumidifier; Control Panel Guide - Dri-Eaz LGR 2800i Guide D'utilisation

IMPORTANT

To help prevent drip tray overflow after using the dehumidifier, always purge the unit before moving.
1. Turn the unit off and allow the plugged in dehumidifier to rest for 10 minutes.
2. Press the PURGE key and while the purge pump is operating, tip the unit back approximately 45° and
hold the unit in place until the purge cycle is complete. The manual purge cycle lasts approximately 10
seconds.
3. Return the unit to the upright position and press PURGE one more time to empty the pump.
Remove the dehumidifier promptly from the job site once these steps have been completed.
and keep it away from anything that could block airflow
into and out of the unit. For more information about
creating an optimum drying environment, contact Dri-
Eaz at 800-932-3030.

OPERATING YOUR DEHUMIDIFIER

Set unit upright
NOTICE: If you transport an i-Series dehumidifier in a
horizontal position, set it upright and let it stand for at
least 30 minutes before you turn it on. When the
machine is horizontal, the oil from the compressor flows
into the refrigerant coils reducing the ability of the
dehumidifier to function. Letting the unit stand upright for
30 minutes allows the oil to flow back into the
compressor.
Set up drain hose
This unit automatically pumps out water on a regular
basis. This dehumidifier is equipped with a quick-
connect fitting for attachment to the provided 40 ft. (12
m) drain hose located in the side pocket. Unwrap the
entire hose and place the open end in a sink, drain,
bucket or outdoors – anywhere that water can drain out
safely. If you use a bucket or other container for water
collection, check it regularly to prevent overflows.
NOTE: Uncoil and straighten the entire drain hose.
Do not leave any of part of the hose coiled on the
unit and do not place the end of the hose higher
than 20 ft. (6 m) above the top of the unit. Also
check for kinks, or obstructions that would restrict
the flow of water. Failure to do so may cause a water
backup in the pump resulting in leakage.
Plug in electrical cord
The i-Series dehumidifier should be plugged into a
GFCI-protected 115 volt outlet rated for at least 15 amps.
Remove the cord from its storage pocket and uncoil it.
Always plug the cord firmly into the unit first, and then
plug the other end into a suitable outlet.
Turn the unit on
The control panel has a display and a touchpad with four
keys. Press the ON/OFF to turn the unit on. The unit
will now go through a compressor delay countdown (up
to 60 seconds in duration) and a self-diagnostics
process, then switch to normal display mode.
07-01674N F410, F411
UNIT ON 00 HRS
INLET 00°F / INLET 00%
The first line of the display shows the total number of
hours the unit has been in operation. This value may be
reset to zero to track job hours (see "Job Hours Reset"
below). The second line of the display alternates
between inlet temperature and inlet humidity.
User Settings Menu
A number of display settings may be changed by the
user. System information can also be displayed. These
items are accessed by pressing
Each press of the key will display the next parameter.
When you reach the parameter you wish to adjust, press
MENU SELECTION to increase the value. Press
DISPLAY MENU again to accept the setting and re-start
the display cycle.
Note that only menu items followed by a greater-than
symbol ( > ) may be adjusted.
All settings and modes are discussed in detail in Control
Panel Guide.
Error messages
If the onboard diagnostics discover a problem, the unit
will display an error message. See "System Messages."

Control Panel Guide

ON/OFF. Press to turn the unit on or off. When the
machine is turned on, the display normally reads
PLEASE WAIT COMP. DELAY and performs a numeral
countdown for a maximum of 60 seconds to 0. This
delay allows time for refrigerant pressures to equalize for
easier starting. Once the unit completes the compressor
delay, the display shows UNIT ON XX HRS and cycles
between INLET XX°F and INLET XX%. NOTE: If no
compressor delay countdown is displayed, a delay is not
necessary and the machine will begin operation
immediately.
DISPLAY MENU. Press to cycle through the display
of additional dehumidifier conditions and User Settings.
3
DISPLAY MENU.
Dri-Eaz Products, Inc.