JVC DLA-M2000LU Manuel D'instructions page 41

(QJB'/$0ERRN 3DJH  7KXUVGD\ $XJXVW     $0
I
Quick Reference Guide for Video Menu Mode
Main Menu in Video Menu Mode (While receiving video-device-related signals)
→
Image adj. (Refer to page 47)
Brightness:
Contrast:
Sharpness:
Color:
Tint:
All reset:
Setting 1
Position:
Tone:
Aspect change:
Decoder:
Setting 2: Press ENTER to enter the Setting 2 submenu
Color temp.
Color temp.:
R-Gain:
G-Gain:
B-Gain:
All-reset:
→
Options (Refer to page 52)
Options 1
Menu display:
Line display:
Keystone:
PC2 (BNC):
Options 2:
Language
Japanese / English* / German / Spanish / Italian / French
→
Information
Input:
Switcher:
Source:
Lamp time:
* : Factory set value.
Brightness of the video image being projected can be adjusted. (–30 to +30, 0*)
Contrast of the video image being projected can be adjusted. (–30 to +30, 0*)
Sharpness of the video image being projected can be adjusted. (–5 to +5, 0*)
Color density of the video image being projected can be adjusted. (–30 to +30, 0*)
Tint of the video image being projected can be adjusted. (–30 to +30, 0*)
Resets above items to the factory set values.
Yes / No
Video screen position and menu position can be adjusted.
Disp. Posi. / Menu
Image tone can be changed. TV*/Cinema (Suitable for the cinema programes)
page 50)
Selectable aspect ratio, 4:3*/16:9.
Selectable color systems, Normally, set to AUTO. (Refer to page 44)
(This item is displayed only when inputting VIDEO or Y/C.)
AUTO*/NTSC/NTSC4.43/PAL/SECAM
Tracking: Normally, no adjustment is required. The lateral size and display area of video image can be
adjusted. (–128 to + 127)
Screen: Selectable screen's aspect ratio. 4:3*/16:9
HDTV: Selectable HDTV format. Normally, set to 1080i, 1080i*/1035i
Setting 1: Press ENTER to return to "Setting 1" submenu.
Adjustable color temperature, Low/Middle*/High.
Will be adjusted to correct reddish or blueish image.
Adjusts the red leve. (0 to 255, the adjustable range varies depending on signals)
Adjusts the green leve. (0 to 255, the adjustable range varies depending on signals)
Adjusts the blue leve. (0 to 255, the adjustable range varies depending on signals)
Reset above items to the factory set values.
Yes/No
15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
5sec* (Line display such as "VIDEO", "Y/C", "PC1", or "PC2" appears on top right of the screen for
5 seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
RGB* or YP P . Set to RGB when a computer device with analog RGB, V, H/Cs signals is
B R
connected to the PC2 terminals. Set to YP
or DTV-format signals (Y, P
Press ENTER to enter the "Option 2" submenu.
Right Left rev.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.: OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:] Selectable sleep times. If no-signal condition continues for the period of
selected time (Unite: Minutes), the projector enters the stand-by mode. 15 / 30
/ 60 / OFF*
Options 1: Press ENTER to return to the "Option 1" submenu.
Language for on-screen display.
(Refer to page 54)
Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, or PC2)
Has no meaning. This display currently has no meaning, ("CH.0" is usually displayed to indicate
that it is not being used.)
Shows the projected image's type of video signal.
Accumulated used hours of the light-source lamp.
DLA-M2000LU/M2000SCU/ LCT0940-002A / ENGLISH
→
→
(Refer to page 50)
→
(Refer to page 46)
→
(Refer to page 45)
P when a device with component signals (Y, B-Y, R-Y)
B R
, P ) are connected to the PC2 terminals.
B R
→
(Refer to page 45)
Menu Operations
(Refer to page 49)
→
(Refer to
→
(Refer to page 45)
39