Install The Door Control - Craftsman Sears 139.18865 Manuel Du Propriétaire

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Installation Step 6
Install the Premium Control Console
Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all moving
parts of the door and door hardware.
The door control is typically attached directly to the
wall. If installing into drywall, drill 5/32" holes and
use the anchors provided. For pre-wired installations
(as in new home construction), Console models
may be mounted to a standard single gang box
(Figure 2).
1. Strip 1/4" of insulation from one end of the bell
wire and connect it to the two screw terminals on
the back of the door control: white to 2, and
white/red to 1.
2. Pry off cover along one side with a screwdriver
blade (see Figure 1). Fasten with 6ABx1-1/4" self-
tapping screws (standard installation) or 6-32x1"
machine screws (pre-wired installation) as
follows:
• Install bottom screw, allowing 1/8" to protrude
above wall surface.
• Position bottom of door control on screw head
and slide down to secure. Adjust screw for snug
fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run the bell wire
up the wall and across the ceiling to the opener.
Use insulated staples to secure the wire in
several places. Be careful not to pierce the wire
with a staple, creating a short.
4. Connect the bell wire to the terminal screws on
Sears
the opener panel: white to 2; white/red to 1.
DoorContrl side/side
5. Position the antenna wire as shown.
7/95
CAUTION
The Chamberlain Group, Inc.
Door Control Premium Console
8/95
Lighted
Push Button
Light
PREMIUM CONTROL CONSOLE
Do not connect to live electrical wiring. Connect
only to 24 Volt low voltage wires. Connection to
live wires or higher voltage may cause serious
injury from shock, burn or electrocution.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it
clearly, and there are no obstructions to door
travel.
Control Console (std installation)
Control Console (pre-wired)
Figure 1
REMOVE & REPLACE COVER
To Replace,
Insert
Top Tabs
First
2-Conductor
Opener
Bell Wire
Terminal Screws
Top
Mounting
Hole
Figure 1
WHITE
POUR ENLEVER ET REMETTRE
Terminal
2
LE COUVERCLE
Screws
Pour remettre,
insérer tout d'abord
RED
les pattes
1
supérieures
Bottom
Mounting
Hole
BACK VIEW
Lock
18
WARNING
Hardware Shown Actual Size
6AB x 1-1/4" Screw
6-32 x 1" Screw
Figure 2
PRE-WIRED
INSTALLATION
To Remove,
Twist
Here
1
2
Figure 2
INSTALLATION
9
1
PRÉ-CÂBLÉE
7
3
5
Pour enlever,
KG
dévisser à
cet endroit
Antenna
Insulated
Staples
Dry Wall Anchors
24 Volt
2-Conductor
Bell Wire
3
9
1
7
3
5
KG
Fil de sonnerie
24 V à
2 conducteurs

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Sears 139.18866Sears 139.18875Sears 139.18876

Table des Matières