Operation - Kärcher B 150 R Mode D'emploi

Information on the initial charge
With the initial charge, the control will
not yet be able to detect which battery
type has been installed. Keep charging
the batteries until the display shows a
full charge (batteries may still not be
completely charged). The next charg-
ing process will have an accurate dis-
play and charge power and the
batteries will be fully charged.
Note:
A "V" to the right of the bar of the bat-
tery indicator shows that the initial
charge has not been performed yet.
Use the appliance until the deep dis-
charge protection switches off the
brush motor and the turbine after the
initial charge of the battery. This proce-
dure is necessary to adjust the battery
indicator. Only then the correct battery
status is displayed.
Removing the batteries
Bring the safety switch into the "0"

position.
Tilt the wastewater tank backwards.

Clamp off the minus pole of the bat-

tery.
Clamp off the remaining cables

from the battery.
Remove the batteries.

Dispose of the used batteries ac-

cording to the local provisions.
Unloading
NOTICE
To take all functions out of operation
immediately, bring the safety switch
into the "0" position.
Four floor boards of the pallet are

fastened with screws. Unscrew
these boards.
Place the boards on the edge of the

pallet. Place the boards in such a
way that they lie in front of the four
wheels of the machine. Fasten the
boards with screws.
Slide the four support beams in-

cluded in the packaging under the
ramp.
Remove the wooden bars in front of

the wheels.
12
Pull the brake lever and push the

appliance down the ramp with the
level pulled.
or
Plug in the Intelligent Key.

Bring the safety switch into the "1"

position.
Set programme selector switch to

transport run.
Set the travel direction switch to

"forward".
Actuate the accelerator pedal.

Drive the appliance off the pallet.

Bring the safety switch into the "0"

position.
Install cleaning head
The procedure for changing the clean-
ing head is described in the chapter
"Maintenance Tasks".
NOTICE
On some models, the cleaning head is
already installed.
Installing the Brushes
The installation of the brushes is de-
scribed in the chapter "Maintenance
Tasks".
Installing the Vacuum Bar
Insert the vacuum bar into the vac-

uum bar suspension in such a man-
ner that the profiled sheet is
positioned above the suspension.
Tighten the wing nuts.

Insert the suction hose.


Operation

DANGER
Risk of injuries. Never use the unit
without protective roof in areas where
the operators can be hit by dropping
objects.
10
-
EN
NOTICE
To take all functions out of operation
immediately, bring the safety switch
into the "0" position.
Adjusting driver's seat
Operate the lever for the seat ad-

justment and move the seat to the
desired position.
Release the seat adjustment lever

and lock the seat in place.
Turning on the Appliance
Take the seating position.

Plug in the Intelligent Key.

Bring the safety switch into the "1"

position.
Turn the programme switch to the

desired function.
Check parking brake
DANGER
Risk of accident. Prior to every opera-
tion, the parking brake must be
checked for proper function on a level
ground.
Turn on the appliance.

Set the travel direction switch to

"forward".
Set programme selector switch to

transport run.
Gently depress drive pedal.

The brake must unlock audibly. The

machine must roll easily on a plane
surface. When the pedal is re-
leased, the brake locks audibly.
Switch off the machine and call the
aftersales service if the above-men-
tioned events do not occur.
Driving
DANGER
Danger of accident. If the machine
does not brake, then proceed as fol-
lows:
If the appliance does not stop when

the accelerator is released on a
ramp with more than 2% inclination,
the safety switch may only be
brought in the "0" position if the
proper mechanical function of the
parking brake has been checked
prior to every operation of the appli-
ance for safety reasons.
Switch off the machine only after it

comes to a complete halt (on an
even surface) and call up the after-
sales service!
Further, follow all warning instruc-

tions for braking.