Table des Matières
Publicité
Additional Safety Warnings Specific for Abrasive Cutting-Off
Operations:
a) Do not "jam" the cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut. Overstressing
the wheel increases the loading and susceptibility to twisting or binding
of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rota-
ting wheel. When the wheel, at the point of operation, is moving away
from your body, the possible kickback may propel the spinning wheel and
the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate and
take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if the power tool is restarted in the
workpiece.
GB
e) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend to sag
under their own weight. Supports must be placed under the workpiece
near the line of cut and near the edge of the workpiece on both sides of
the wheel.
f) Use extra caution when making a "pocket cut" into existing
walls or other blind areas. The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper. Follow
manufacturers recommendations, when selecting sanding
paper. Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging, tearing of the
disc or kickback.
Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing, do
not allow any interference of the wire wheel or brush with the
guard. Wire wheel or brush may expand in diameter due to work load
and centrifugal forces.
Additional Safety and Working Instructions
When grinding metal, flying sparks are produced. Take care that no
persons are endangered. Because of the danger of fire, no combustible
materials should be located in the vicinity (spark flight zone). Do not use
dust extraction.
Avoid flying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is running.
Immediately switch off the machine in case of considerable vibrations
or if other malfunctions occur. Check the machine in order to find out
the cause.
Under extreme conditions (e.g. smooth-grinding metals with the
arbour and vulcanized fibre grinding wheel), significant contamination
English
14
14
can build up on the inside of the angle grinder. For safety reasons,
in such conditions a ground fault interrupter must be connected in
series. If the ground fault interrupter trips the machine must be sent
for service.
Chips and splinters must not be removed while the machine is running.
Do not let any metal parts enter the airing slots - danger of short circuit!
MAINS CONNECTION
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Appliances used at many different locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off.
Inrush currents cause short-time voltage drops. Under unfavoura-
ble power supply conditions, other equipment may be affected. If
the system impedance of the power supply is lower than 0,2 Ohm,
disturbances are unlikely to occur.
SPECIFIED CONDITIONS OF USE
The angle grinder is intended for grinding and cutting metal, stone
and ceramic materials as well as sanding and wire brushing.
Use the cutting guard from the accessories range for cutting
application.
Please refer to the instructions supplied by the accessory manu-
facturer.
The machine is suitable only for working without water.
WORKING INSTRUCTIONS
For accessories intended to be fitted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept the
spindle length.
Always use and store the cutting and grinding wheels according to
the manufacturer's instructions.
Always use the correct guard for cutting and grinding.
The adjusting nut must be tightened before starting to work with
the machine.
Always use the auxiliary handle.
The workpiece must be fixed if it is not heavy enough to be steady.
Never move the workpiece towards the rotating wheel by hand.
ELECTRONICS
AGV 13-115 XSPDE, AGV 13-125 XSPDE:
The machine has an overload and anti-kickback safety function
and stops if it is overloaded.Please note that the machine will
automatically accelerate back to its original operating speed if the
load is removed from it.After it has reached its operating speed the
machine is ready for use again.
A zero-voltage switch prevents the machine from restarting after a
power cut. When resuming work, switch the machine off and then
switch it back on again.
SOFT START
AGV 13-115 XSPDE, AGV 13-125 XSPDE:
Electronic soft start for save use prevents jerky run-up of the
machine.
Publicité
Table des Matières
