Technical Data; Recommended Size Of The Trunks For Splitting; Operation - EINHELL HSP 6/104 Mode D'emploi

Anleitung HSP_6-104_SPK1:Anleitung HSP41-1_HSP51_SPK1
GB
securing screws (Fig. 16 / Item A) from the washers
(Fig. 16 / Item B) and the star nuts (Fig. 16 / Item C).
Insert the securing screws A from below through the
oval holes in the trunk holding plates and the holes in
the hand guards as shown in Figure 17 and secure
then by fitting the washers B and star nuts C to them
from above (Fig. 18). The trunk holding plates can be
adjusted to the trunk thickness using the oval holes.
4.6 Fitting the chain to adjust the splitter height
(Fig. 19-21)
First undo the lock nut on the chain hook (Fig. 19).
Secure the chain hook to the hole provided for it next
to the chain holder behind the splitter as shown in
Figure 20. The chain is designed to limit the height of
the splitter. To do this, move the splitter
approximately to the required position, switch off the
machine (Fig. 29) and attach the chain in the
appropriate position (Fig. 21).
4.7 Fitting the trunk support (Fig. 22-26)
The trunk support can be installed at three different
heights (Fig. 22):
Position A: Max. log length 520 mm
Position B: Max. log length 770 mm
Position C: Max. log length 1040 mm
There are three attachment devices at different
heights on the wood splitter for this purpose. To use
the trunk support, the locking levers on the
appropriate attachment device must be moved
upwards (Fig. 23) so that they are vertical (Fig. 24).
The trunk support must then be pushed into the
attachment device from the front (Fig. 25) and
secured by returning the locking levers to their
original positions (Fig. 26).
4.8 Filling with hydraulic oil
The wood splitter must be filled with oil before it is
started for the first time. Refer to section 10
"Changing the hydraulic oil"
5. Technical data of the HSP 6/104
Voltage: 230 V ~ 50 Hz
Power rating:
Idle speed:
Protection type:
Max. splitting force:
Splitting lift:
Splitting speed
Downwards:
Upwards:
Trunk holding capacity:
Diameter: 100 -320 mm
Length: 150 -1040 mm
18
Oil quantity:
Weight:
Technical data of the HSP 6/104 D
Voltage:
Power rating:
Idle speed:
Protection type:
Max. splitting force:
Splitting lift:
Splitting speed
Downwards:
Upwards:
Trunk holding capacity:
Diameter:
Length:
Oil quantity:
Weight:
6. Recommended size of the trunks for
splitting
Trunk holding capacity:
100-320 mm (diameter) x 150-1040 mm (length)
1. The trunk diameters given above are indicative
only.
Thin pieces of wood can be very difficult to split if
they contain knot holes or have very tough fibers.
On the other hand, it may be possible to split
thicker pieces of wood if they have smooth and
loose fibers.
2. Never attempt to force the wood splitter to split
excessively hard pieces of wood under cylinder
pressure for more than 5 seconds. Overheated
oil under pressure may cause damage to the
machine. It is very important that you stop the
machine if the wood splitter fails to split the wood
at the first attempt. Then turn the trunk through
90° and attempt to split it again. If the wood still
fails to split this means that it is too hard for the
capacity of the machine and must be removed to
2200 W
avoid damaging the wood splitter.
2950 rpm
IP 54
6 t

7. Operation

480 mm
1. Plan your work area. To work in safety and
0.032 m/s
save yourself a lot of effort, plan your work area
0.12 m/s
in advance. Position the trunks where they are
easy to reach. Allocate an area for stacking the
split wood or load it onto a wheelbarrow or other
15.12.2006 9:28 Uhr
2.5 -4.0 l
99 kg
400 V 3 ~ 50 Hz
2200 W
2950 rpm
IP 54
6 t
480 mm
0.032 m/s
0.12 m/s
100 -320 mm
150 -1040 mm
2.5 -4.0 l
99 kg
Seite 18