Installation; Installing The Polemounted Pruner Attachment (01- 02); Extending/Shortening The Telescopic Pole (03); Installing The Guide Rail And Saw Chain (04 - 08) - AL-KO CSA 2020 Mode D'emploi

GB
■
This appliance must not be used by unautho-
rised persons unless they are supervised by
a person responsible for their safety or have
been instructed on how to use the appliance.
Unauthorised persons include, for example:
■
Persons (including children) with limited
physical, sensory or mental aptitude
■
Persons who have no experience and/or
knowledge of the appliance.
■
Children must be supervised and instructed
so they do not play with the appliance.
■
Dry unused appliances and store in a closed
place. Unauthorised persons and children
must not have access to the appliance.

4 INSTALLATION

WARNING!
Danger of serious injury
If an incompletely mounted polemounted
pruner is used, serious injury can be
caused.
■
Only use the polemounted pruner
when it has been fully mounted.
■
Before each use, perform a visual in-
spection in order to check that the
polemounted pruner is complete and
does not contain damaged, worn or
loose components. Safety and pro-
tective devices must be intact.
CAUTION!
Danger of laceration injuries.
The sharp edges of the saw chain can
cause laceration injuries when assem-
bling.
■
Before installation, remove the re-
chargeable battery.
■
Wear safety gloves when installing
the saw chain and the guide rail.
4.1 Installing the polemounted pruner
attachment (01- 02)
1. Put the coupling (01/2) onto the telescopic
pole (01/3) and push the coupling into the
polemounted pruner head (01/1) as far as it
will go (01/a).
2. Screw (02/a) the coupling (02/1) as far as it
will go in the direction of the polemounted
pruner head (02/2).
36
4.2 Extending/shortening the telescopic
pole (03)
The telescopic pole (03/1) is infinitely adjustable.
This means the length can be adjusted as re-
quired for the work.
1. Unscrew (03/a) the clamping screw (03/2)
until the clamp is released.
2. Move the telescopic pole until the desired
length is set (03/b)
3. Screw the clamping screw tight.
4.3 Installing the guide rail and saw chain
(04 – 08)
CAUTION!
Risk of injury on the saw chain
The cutting edges of the saw chain are
very sharp so that cutting injuries can oc-
cur when handling the saw chain. Before
all work with the saw chain, heed the fol-
lowing:
■
Switch off the appliance and remove
the rechargeable battery.
■
Wear protective footwear.
1. Loosen (04/a) the fastening screw (04/1) of
the chain sprocket cover (04/2). Remove the
fastening screw and chain sprocket cover.
2. Use the screwdriver on the Allen key to loos-
en the chain tensioning screw (05/1). Turn
the chain tensioning screw until the chain
tensioning pin (05/2) is at the rear thread end
(05/a).
3. Insert the saw chain:
■
Align (06/a) the cutting teeth (06/1) of the
saw chain (06/2) that are to lie at the top
of the guide rail to the tip of the guide rail
(06/3).
Note: Make sure that the chain is cor-
rectly mounted!
■
Place the saw chain in the groove (06/4)
of the guide rail and guide completely
around the guide rail.
4. Lay the guide rail together with the saw chain
laid on it in the open housing:
■
Lay the saw chain (07/1) around the drive
sprocket (07/2).
■
Align the guide rail (07/3) in such a way
that the two guide pins (07/4) grip in the
slotted hole (07/5) of the guide rail.
Installation
CSA 2020