Cord Sets And Connection Plugs; 120 Vac, 20 Amp, Duplex Receptacle; How To Use The Generator; Grounding The Generator - Generac GP Série Manuel Du Propriétaire

Masquer les pouces Voir aussi pour GP Série:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Operation

2.2 CORD SETS AND CONNECTION PLUGS

2.2.1 120 VAC, 20 AMP, DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 13.5 Amp
push-to-reset circuit breaker (Figure 6). 13.5 Amps of current may be
drawn from each socket, however, total power drawn must be kept
within data plate ratings. Use only high quality, well insulated, 3-wire
grounded cord sets rated for 125 Volts at 20 Amps (or greater).

2.3 HOW TO USE THE GENERATOR

If there are any problems operating the generator, please call the
generator helpline at 1-888-436-3722.
Never operate in an enclosed area or indoors!
NEVER use in the home, in a vehicle, or in
partly enclosed areas such as garages, EVEN
IF doors and windows are open! ONLY use
outdoors and far from open windows, doors,
vents, and in an area that will not accumulate
deadly exhaust.
The engine exhaust fumes contain carbon
monoxide, which you cannot see or smell.
This poisonous gas, if breathed in sufficient
concentrations, can cause unconsciousness or
even death.
Adequate, unobstructed flow of cooling and
ventilating air is critical to correct generator
operation. Do not alter the installation or
permit even partial blockage of ventilation
provisions, as this can seriously affect safe
operation of the generator. The generator
MUST be operated outdoors.
This exhaust system must be properly
maintained. Do nothing that might render the
exhaust system unsafe or in noncompliance
with any local codes and/or standards.
Always use a battery operated carbon
monoxide alarm indoors, installed according to
the manufacturers instructions.
6

2.3.1 GROUNDING THE GENERATOR

This generator has an equipment ground that connects the generator
frame components to the ground terminals on the AC output
receptacles (see NEC 250.34 (A) for explanation). This allows the
generator to be used as a portable without grounding the frame of the
generator as specified in NEC 250.34.
2.3.1.1
SPECIAL REQUIREMENTS
There may be Federal or State Occupational Safety and Health
Administration (OSHA) regulations, local codes, or ordinances that
apply to the intended use of the generator.
Please consult a qualified electrician, electrical inspector, or the local
agency having jurisdiction:
In some areas, generators are required to be registered with local
utility companies.
If the generator is used at a construction site, there may be additional
regulations which must be observed.
2.3.2 CONNECTING THE GENERATOR TO A BUILDING'S

ELECTRICAL SYSTEM

When connecting directly to a building's electrical system, it is
recommended that a manual transfer switch is used. Connections
for a portable generator to a building's electrical system must be
made by a qualified electrician and in strict compliance with all
national and local electrical codes and laws.
Figure 7 - Grounding the Generator

2.3.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles. DO NOT
connect 3-phase loads to the generator. DO NOT connect 50 Hz loads
to the generator.
• Let engine stabilize and warm up for a few minutes after starting.
• Plug in and turn on the desired 120 or 240 Volt AC, single phase,
60 Hz electrical loads.
• Add up the rated watts (or amps) of all loads to be connected
at one time. This total should not be greater than (a) the rated
wattage/amperage capacity of the generator or (b) circuit breaker
rating of the receptacle supplying the power. See "Don't Overload
the Generator".

Publicité

Table des Matières
loading

Table des Matières