Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Page 14
6.4
Test the AquaLink Z4
Perform a basic installation test to make sure the
controller turns on the filter pump, the pool heater,
and spa pump and spa heater (if applicable). Test the
controller installation using the Manual Control menu to
turn specific equipment ON/OFF manually.
6.4.1
Test Filter Pump ON/OFF
MAIN > DEVICES > FILTER PUMP
Zodiac
Zodiac
12:40PM
12:40PM
Pool Mode
On
Pool Mode
On
Pool Heater
80°F
Pool Heater
80°F
Spa Mode
>
Spa Mode
O
Spa Heater
>
Spa Heater
O
Aux1
O
Settings
>
Aux2
O
Devices
>
Settings
>
Service Mode
>
Devices
>
•
Highlight FILTER PUMP and press Select to turn
the filter pump ON.
After a couple of minutes, you should hear the
filter pump go on.
6.4.2
Test Spa Pump ON/OFF
(if applicable)
MAIN > DEVICES > SPA PUMP
Zodiac
Zodiac
12:40PM
12:40PM
Pool Mode
On
Pool Mode
On
Pool Heater
80°F
Pool Heater
80°F
Spa Mode
Spa Mode
O
O
Spa Heater
O
Spa Heater
O
Settings
Settings
>
>
Devices
>
Devices
>
Service Mode
>
Service Mode
>
•
Highlight SPA PUMP and press Select to turn the
spa pump ON.
After a couple of minutes, you should hear the spa
pump go on.
AquaLink
Z4 Controller | Installation Manual
®
Filter Pump
Spa
Pool Heat
Spa Heat
Solar Heat
Devices
Devices
Filter Pump
O
Filter Pump
On
Spa Pump
O
Spa Pump
O
Pool Heat
O
Pool Heat
O
Spa Heat
O
Spa heat
O
Solar Heat
O
Solar Heat
O
More
Devices
Devices
Filter Pump
O
Filter Pump
O
Spa Pump
On
Spa Pump
On
Pool Heat
Pool Heat
O
O
Spa heat
O
Spa heat
O
Solar Heat
Solar Heat
O
O
More
More
6.4.3
Test Pool Heater ON/OFF
MAIN > DEVICES > POOL HEATER
Devices
Devices
Filter Pump
O
O
Spa
O
O
Pool Heat
O
O
Spa Heat
O
O
Solar Heat
O
O
More
More
1.
Highlight POOL HEATER and press Select.
2.
Scroll up/down to set temperature then press
Select. After a couple of minutes, you should hear
the pool heater go on.
6.4.4
Test Spa Heater ON/OFF
(if applicable)
NOTE: To test the spa heater installation, first turn on
the auxiliary JVA associated with the spa (see
Section 7.10 Assign JVA) and wait 35 seconds
before turning on the spa heater through the UI.
MAIN > DEVICES > SPA HEATER
Zodiac
Manual Control
12:40PM
Filter Pump
O
Pool Mode
On
Spa
O
Pool Heater
80°F
Pool Heat
O
Spa Mode
O
Spa Heat
Spa Heater
O
O
Solar Heat
AUX1
O
>
AUX2
>
Settings
>
More
Devices
>
1.
Highlight SPA HEATER and press Select.
2.
Scroll up/down to set temperature then press
Select. After a couple of minutes, you should hear
the spa heater go on.
Pool Heat
Pool Heat
Enabled
Enabled
Set to: 80°F
Set to: 80°F
Devices
Spa Heat
Enabled
Filter Pump
O
Spa Pump
O
Pool Heat
O
Set to: 102°F
Spa Heat
On
Solar Heat
O
More
Publicité
Chapitres
Table des Matières
