Table des Matières
Publicité
7. CUTTING RANGE
CAPACITE DE COUPE
CAPACIDAD DE CORTE
MATERIAL
CHARGE DE RUPTURE A LA TRACTION
MATIERE
WERKSTOFF
MATERIAL
MATERIALE
Copper Cuivre
Kupfer Cobre Rame
Aluminium Aluminium
Aluminium Aluminio Alluminio
Almelec Almelec
Alu-Legierung Almelec Aldrey
Steel
Acier
Stahl
Acero
Acciaio
Multi strands steel
(strands qty. ≥ 200)
Acier extra-souple
( ≥ 200 brins)
Mehrdrähtiger Stah
l
( Draht ≥ 200)
Acero flex
( ≥ 200 Hilos)
Acciaio extraflex
( N°fili elem.≥ 200)
ACSR
Aluminium-Acier
Aluminium/Stahl
ACSR
Alluminio/Acciaio
Steel
Acier
Stahl
Acero
Acciaio
Copper Cuivre
Kupfer Cobre Rame
Aluminium Aluminium
Aluminium Aluminio Alluminio
(*)
TYPICAL EXAMPLES
A TITRE D' EXEMPLES
ALGUNOS EJEMPLOS INDICATIVOS
ESEMPI INDICATIVI
SCHNEIDBEREICH
CAPACITÀ DI TAGLIO
TENSILE STRENGTH
MAX CUTTING DIAMETER
DIAMETRE EXTERIEUR MAX. SECTIONNABLE
ZUGFESTIGKEIT
MAX SCHNEIDDURCHMESSER
CARGA DE ROTURA
DIAMETRO MAX DE CORTE
CARICO DI ROTTURA A TRAZIONE
DIAMETRO ESTERNO MAX TAGLIABILE
(daN/mm
2
)
(lbs/sq.in.)
(mm)
≤ 41
≤ 59,450
40
≤ 20
≤ 29,000
40
≤ 34
≤ 49,300
40
(*)
≤ 180
≤ 261,000
7 x 3,0 : ø = 9,0 mm
7 x 0.118 = ø out.0.354
19 x 2,1 : ø = 10,5 mm
19 x 0.083 = ø out. 0.413
19 x 2,3 : ø = 11,5 mm
19 x 0.091 = ø out. 0.453
18
≤ 180
≤ 261,000
40
(*)
≤ 180
≤ 261,000
26 x 2,50 + 7 x 1,95 : ø = 15,85
26 x 0.098 + 7x 0.077 : ø out 0.624
26 x 3,06 + 7 x 2,38 : ø = 19,38
26 x 0.120 + 7x 0.094 : ø out 0.763
26 x 3,60 + 7 x 2,80 : ø = 22,80
26 x 0.142 + 7x 0.110 : ø out 0.897
54 x 3,50 + 19 x 2,10 : ø = 31,50
54 x 0.138 + 19x 0.082 : ø out 1.240
54 x 4,36 + 19 x 2,62 : ø = 39,20
54 x 0.172 + 19x 0.103 : ø out 1.543
≤ 60
≤ 87,000
18
≤ 42
≤ 60,900
20
≤ 30
≤ 43,000
30
≤ 25
≤ 36,250
32
≤ 16
≤ 23,200
40
EINIGE BEDEUTENDE ANWENDUNGEN
A microprocessor controls the tool operation and automatically cuts out the motor, saving
energy and extending battery life.
The residual battery capacity level is automatically displayed after every cycle.
The part reference "B-TC04 or B-TC04A" includes the following:
– Basic tool complete with battery and shoulder strap.
– Spare battery.
– Battery charger.
(inches)
– Steel carrying case "VAL B-TC04".
1-9/16"
1-9/16"
2. INSTRUCTIONS FOR USE
1-9/16"
2.1) Preparation
The tool can be easily carried using either the handle or the shoulder strap (11) attached to
(*)
the rings (15 and 19).
With the tool in the rest position operate as follows:
– Insert the conductor between the blades at the desired cutting point.
For a running conductor,remove the locking pin (04) and open the tool head.
0.709
Warning: the opening of upper blade must be done when the tool is in rest position,
(lower blade (14) completely retracted).
1-9/16"
– With the conductor on the lower blade (14), close the tool head and fully insert the locking
(*)
pin (04).
B
EFORE CARRYING OUT FURTHER CUTTING OPERATIONS MAKE SURE THE LOCKING
(04)
PIN
0.709
.
HEAD
0.787
2.2) Blade advancement
– Operate push-button (18) housed inside the pressure release button (17) to activate the
1.181
motor-pump group for the advancement of the lower blade.
This fi rst stage rapidly closes the lower blade (14) to the conductor.
1.260
– To halt the advancement, release the push-button (18) and the motor will cut out.
Make sure that blades are exactly positioned at the desired cutting point, otherwise
1.575
re-open blades following instructions as § 2.5 and reposition the conductor.
2.3) Cutting
By keeping push-button (18) pressed down the motor continues to operate: the lower blade
advances gradually until the conductor is fully cut.
36
5
(Ref. to Figs. 1 and 6)
:
IS COMPLETELY INSERTED
A PARTIAL INSERTION MAY DAMAGE THE TOOL
ENGLISH
Publicité
Table des Matières
