Jacuzzi J-300 Série Manuel D'installation Et Utilisation Et Entretien page 39

1. Media Locker Handle
Slide the handle to lock and unlock the protective door.
2. Power Button
Press power button once to turn "ON" stereo system. Press a se-
cond time to place the stereo in "Standby" mode and the red
light will remain illuminated.
3. Auxiliary Input Jack Connector
Allows you to connect an auxiliary device by using a 3.5 mm cable.
4. Universal Serial Bus (USB) Device Connector
Allows you to connect your device via a USB port and a US cable
compatible with your device.
5. Auxiliary Device Holding Base
The removable base securely holds the Auxiliary device, such
as an iPod®/MP3/iPhone®, in place. It can be removed for larger
devices.
6. 3.5 mm Cable (purchased separately)
Use this cable to connect your Auxiliary or MP3 device to the
stereo via the "AUX" connection.
7. Cavo Apple USB da 30 pin (acquistato separatamente)
Use this cable to connect your compatible iPod, iPhone or MP3
device to the stereo via the "USB" connection.
WARNING: RISK OF ELECTRICAL SHOCK HAZARD
EXISTS AND EQUIPMENT DAMAGE! Never install or
remove electrical devices (e.g. Apple device/MP3/USB/
AUX/Bluetooth) while hands are wet or while sitting
partially or fully immersed in the spa!
CAUTION: Never leave electrical devices in the Media Locker
when spa is not is use to prevent damage from outdoor elemen-
ts! Never spray Media Locker with a pressurized water hose for
any reason! Damage to the device or spa stereo system caused
by water intrusion is not covered under the manufacturer's war-
ranty! Damage to Media Locker port or electrical devices due
to excessive force or improper alignment during installation or
removal from Media Locker is not covered under warranty.
Pairing the Remote and Stereo
In order for the remote to operate the stereo, you
need to pair them using the following method:
- Make sure the stereo unit is in "Standby" mode. LED power
light will be red.
- Press any button on the remote to turn it ON. The remote
LCD display will read "No Link. "
- Press and hold the "Mode" button on the remote. At the
same time, press and hold the power button on the stereo
for 2 seconds
- The remote LCD display will read "Welcome, " "Load" and "Ra-
dio" if the pairing sequence was successful.
Audio Settings
The Audio button, provides access to many of the stereo's settin-
gs. By continually pressing the Audio button you can scroll and
adjust the following functions: BAS-TRE-BAL-FAD-DSP-AREA-
LOUD-DX-STEREO (respectively).
Note: You can adjust the settings by pressing the Audio button,
making your adjustments and pressing the Audio button to go the
next feature. If you exit the setting menus continually press the Au-
dio button until you reach the setting you would like to adjust.
Press the Audio button once to access the bass set-
ting. The LCD display will change to "BAS 0, " Figure D.
Press the Up button to adjust the setting to a maxi-
mum of +5. Press the Down button to adjust the setting
down to -5.
Note: The default setting is "0." This feature is disabled when a "Di-
gital Sound Processor" (DSP) setting is active such as "Rock," "Clas-
sic," or "Pop."
Press
the treble setting. The LCD display will change to "TRE
0, " . Press the Up button to adjust the setting to a maxi-
mum of +5. Press the Down button to adjust the setting
down to -5.
Note: The default setting is "0." This feature is disabled when a "Di-
gital Sound Processor" (DSP) setting is active such as "Rock," "Clas-
sic," or "Pop."
Press the Audio button 3 times to access the balance setting. The
LCD display will change to "BAL L=R, " . Press the Up button to adjust
the setting to a maximum of 10R (only the right side speakers
will have volume). Press the Down button to adjust the setting
down to 10L (only the left side speakers will have volume).
Press the Audio button 4 times to access the fade set-
ting. The LCD display will change to "FAD F=R, " . Press
the Up button to adjust the setting to a maximum
of 10F (only the front speakers will have volume).
AUDIO
MODE
Press the Down button to adjust the setting down to 10R
(only the rear speakers will have volume).
1 2 3
DIR - DIR + REPEAT RANDOM
Press the Audio button 5 times to access the DSP setting. The
LCD display will change to "DSP OFF". Press the Up button to se-
lect one of the preset settings such as Rock, Classic or Pop.
39
Bass Setting
Treble Setting:
the Audio button
Balance Setting
Fade Setting
Digital Sound Processor (DSP) Setting
2 times to access