Jacuzzi J-300 Série Manuel D'installation Et Utilisation Et Entretien page 35

4. Gently rotate the larger (rear) valve body 1/3 turn counter-
clockwise to unlock the drain valve.
5. Pull the larger (rear) body outward to open drain.
6. After the spa drains, perform steps 2-5 in reverse order to clo-
se the drain prior to refilling the spa.
7. After refilling, turn on power to the spa and follow the steps
listed under "Spa Fill Up Procedure".
N.B.: Always fill your spa through both filter wall fittings.
Cleaning The Spa Interior
To preserve the sheen of your spa's surface, it is crucial that you
avoid using abrasive cleaners or cleaners which have adverse che-
mical effect on the surface. If you are not certain as to the suitabili-
ty of a particular cleanser, consult your authorized Jacuzzi dealer.
Regardless of the cleanser used, use extreme care to assure that no
soap residue is left on the surface. This could cause severe sudsing
when the spa is refilled.
Pillow Care
C
B
A
Remove and clean the headrest pillows as needed with soapy
water using a cloth or soft-bristle brush.
Always remove the pillows when adding chemical shock tre-
atment to the spa water. The pillows can be returned to the spa
when the sanitizer reading drops below 4 ppm.
To remove pillows:
1. Grasp pillow insert (A) with finger tips and gently pry outward
from pillow base (B).
2. Grasp pillow base (B) with finger tips and gently pry outward
from spa shell (C).
3. Assemble in reverse order after cleaning.
Vinyl Cover Care and Maintenance
Your Jacuzzi cover has a vinyl encasement. This vinyl encasement
is attractive and durable. Monthly cleaning and conditioning is
strongly recommended to maintain and increase the longevity of
your cover.
To Clean and Condition the Vinyl Cover
1. Use a garden hose to loosen debris and dirt.
2. Using a large sponge or a soft bristle brush, use diluted or
mild soap and scrub the vinyl top. Rinse clean and do not allow
soap to dry on cover. Do not use soap on the underside of the
cover.
3. Please check with your Jacuzzi Dealer for recommended co-
ver care and conditioning products. Condition using non-petro-
leum based conditioners to keep the vinyl supple and threads/
stitching from drying out. Do not use solvents, abrasive cleaners
or strong detergents. Do not use products that contain silicone
or alcohol.
To Clean and Condition the ProEndure™ cover:
1. Brush off dirt, leaves and any loose debris.
2. Thoroughly hose down the cover.
3. Using a large sponge or a soft bristle brush, use diluted or
mild soap (such as woolite or dreft, no detergents) and scrub the
cover. Allow the solution to soak in.
4. Rinse clean and do not allow soap to dry on cover. Continue
to rinse until all the soap solution is removed. Do not use soap
on the underside of the cover. The fabric dries quickly allow it to
air. Do not apply heat or machine dry.
5. Retreating the fabric, using 303 High Tech Fabric Guard™,
after cleaning is highly recommended. Follow the instructions
from the manufacturer.
6. Additional cleaning and care information may be found at
www.sunbrella.com
NOTE: Do not use solvents, abrasive cleaners or strong deter-
gents. Do not use products that contain silicone or alcohol.
Additional Care and Maintenance Instructions:
1. Debris can accumulate on the spa cover. Removal of snow or
other debris will help to avoid breakage of the foam cores.
2. Be sure to lock the cover straps to secure the cover from
unwanted or accidental entry.
3. Do not place heavy objects on the vinyl.
4. Do not walk, sit or stand on the cover.
5. Do not drag or use the flaps/skirt or the cover lock straps to
remove the cover.
6. Use only recommended cover lift systems.
7. Use only chemicals and cleaners recommended by Jacuzzi.
8. Remember to keep spa covered when not in use. Maintaining
proper water levels assures efficient operation and efficient
electrical usage.
9. Do not expose your spa to the sun for extended periods of
time as UV rays can damage the interior surface.
10. Use caution when removing cover. Before removing cover,
assure all locks have been released to avoid lock breakage and
or cover strap damage.
Tool Free Access Door
The Tool Free Access door provides fast access to the equipment
bay and components without the need of tools. To remove the
door, follow the steps below.
Note: To avoid any injuries, more than one individual must per-
form these steps.
35