Attaching The Hose - Black & Decker FSMH1321 Mode D'emploi

ENGLISH
Attachin
Removing the hand held steam cleaner (Fig. B)
Removing a cleaning pad
Filling the water tank (Fig. Q)
g the hand held steam cleaner (Fig. B)
Holding the back of the steam mop body (11) push the
body (11) making sure it sits correctly over the interface
(11a) and clicks securely into place.
Push the release button (10) on the main body (11) and lift
the hand held steam cleaner (5) off the interface (11a) and
away from the main body (11).
Attaching a cleaning pad (Fig. C)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
side facing up.
Lightly press the steam mop down onto the cleaning pad
(13).
Note: This unit may be supplied with a standard floor cleaning
head (12) or a steam burst cleaning head (12a). In either case
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
Return the handle (8) to the upright position and turn the
Wait until the steam mop cools down (approximately 5
minutes).
Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
Fill the water tank with water (Do not use any additives or
chemicals).
Warning! When filling, detach from main unit and maintain in
a horizontal position.
8
u
hand held steam cleaner (5) firmly into the steam mop
u
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
u
use these instructions to fit a cleaning pad.
u
steam mop 'OFF'.
u
u
Open the filler cap (4) by flipping it up.
u
u
(Original instructions)
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - O)

Attaching the hose

Attaching the carpet glider (12b) (For use on
carpets only)
Removing the carpet glider
Warning! Your water tank has a 0.5 litre capacity. Do not over
Note! Ensure the filler cap is firmly secured.
Lightly press the steam mop down onto the carpet glider
(12b) until it clicks into place.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (8) to the upright position and turn the
Wait until the steam mop cools down (approximately 5
minutes).
Place the front of your shoe onto the carpet glider removal
Lift the steam mop up and off the carpet glider.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
Press the steam hose release button (16a) on the steam
hose (16).
Connect the steam hose (16) to the hand held steam
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
fill the tank.
Close the filler cap (4).
u
Place the carpet glider (12b) on the floor.
u
Attach a cleaning pad to the floor cleaning head (12)
u
u
u
steam mop 'OFF'.
u
u
tab and press down firmly.
u
u
u
escapes from the joint, the hose is incorrectly fitted. Switch off,
allow the unit to cool then remove and refit the hose.