Audio Settings - JVC KD-R449 Manuel D'instructions

AUDIO SETTINGS

To Do this
Select a preset
Press EQ repeatedly.
equalizer
FLAT (default), NATURAL, DYNAMIC, VOCAL BOOST, BASS BOOST, USER
Store your own 1
Press and hold EQ.
sound settings
2
Turn the volume knob to make a selection, then press the knob.
SUB.W * 1 :
BASS LVL:
MID LVL:
TRE LVL:
• The setting is stored to [USER] in EQ.
• To return to the previous item, press G T/P.
• To exit, press EQ.
* 1
Displayed only when [L/O MODE] is set to [SUB.W] and [SUB.W] is set to [ON].
Other settings
1
Press and hold MENU.
2
Turn the volume knob to select [PRO EQ] or [AUDIO], then press the knob.
3
Turn the volume knob to make a selection (see the table below), then press the knob.
Repeat step 3 until the desired item is selected.
4
Press MENU to exit.
PRO EQ
1 BASS / MIDDLE / TREBLE: Select a sound tone.
2 Adjust the sound elements of the selected sound tone.
BASS Frequency:
Level:
Q:
MIDDLE Frequency:
Level:
Q:
TREBLE Frequency:
Level:
Q:
The setting is stored to [USER] in EQ.
–08 to +08 Default: (00)
–06 to +06 (00)
–06 to +06 (00)
–06 to +06 (00)
60/ 80/ 100/ 200 Hz Default:
–06 to +06
Q1.0/ Q1.25/ Q1.5/ Q2.0
0.5/ 1.0/ 1.5/ 2.5 kHz Default: (1.0 kHz)
–06 to +06
Q0.75/ Q1.0/ Q1.25
10.0/ 12.5/ 15.0/ 17.5 kHz Default: (10.0 kHz)
–06 to +06
Q FIX
AUDIO
FADER * 2 * 3
R06 — F06 (00): Adjusts the front and rear speaker output
balance.
BALANCE * 3
L06 — R06 (00): Adjusts the left and right speaker output balance.
BASS BOOST +01 / +02: Selects your preferred bass boost level. ; OFF: Cancels.
LOUD LOW / HIGH: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; OFF: Cancels.
VOL ADJUST –05 — +05 (00): Presets the volume adjustment level of each
source (compared to the FM volume level). Before adjustment,
select the source you want to adjust. ("VOL ADJ FIX" appears if FM
is selected.)
L/O MODE SUB.W / REAR: Selects whether rear speakers or a subwoofer are
connected to the REAR/SW line out terminals on the rear panel
(through an external amplifier).
SUB.W * 4
ON / OFF: Turns on or off the subwoofer output.
SUB.W LPF * 5
THROUGH: All signals are sent to the subwoofer. ; LOW 55Hz /
MID 85Hz / HIGH 120Hz: Audio signals with frequencies lower
than 55 Hz/ 85 Hz/ 120 Hz are sent to the subwoofer.
SUB.W LEVEL * 5
–08 — +08 (00): Adjusts the subwoofer output level.
BEEP ON / OFF: Activates or deactivates the keypress tone.
TEL MUTING * 6
ON: Mutes the sounds while using the cellular phone (not connected
through KS-BTA100). ; OFF: Cancels.
(80 Hz)
(00)
AMP GAIN LOW POWER: Limits the maximum volume level to 30. (Select if
(Q1.0)
the maximum power of each speaker is less than 50 W to prevent
damaging the speakers.) ; HIGH POWER: The maximum volume
(00) level is 50.
(Q1.25)
* 2 If you are using a two-speaker system, set the fader level to [00].
* 3
This adjustment will not affect the subwoofer output.
(00) * 4
Displayed only when [L/O MODE] is set to [SUB.W].
(Q FIX) * 5 Displayed only when [SUB.W] is set to [ON].
* 6
Does not work if [BT ADAPTER] is selected for [AUX] in [SRC SELECT].
8
Default: XX