Setting The Second Camera; Setting The Camera For Camera View Mode - Pioneer AVH-4200NEX Manuel Du Propriétaire

System settings
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
45
2 Touch [Camera settings].
3 Touch [Reverse Gear Setting].
 Battery:
The polarity of the connected lead is positive.
 Ground:
The polarity of the connected lead is negative.
p If no camera connection is made and the camera polarity
setting is wrong, a black screen is displayed as the rear view
camera image immediately after startup. In such a case,
press and hold the MUTE button to release the rear view
camera screen and then change the camera polarity setting
to "Battery".
Setting the reversed image display
for the rear view image
You can set whether to reverse the rear view camera images to
be displayed on the front screen.
The default setting is "Off".
p This setting is available only when you stop your vehicle in a
safe place and apply the parking brake.
p This function is available when "Back Camera Input" is set
to "On".
 Refer to Setting rear view camera activation on page 45
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
45
2 Touch [Camera settings].
3 Touch [Back Camera: Reverse Video] to switch
"On" or "Off".
Setting the parking assist guidelines
Displaying the parking assist
guidelines
You can set whether to display the parking assist guidelines on
the rear view camera images when backing up your vehicle.
The default setting is "Off".
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
45
2 Touch [Camera settings].
46
3 Touch [Parking Assist Guide] to switch "On" or
"Off".
Adjusting the parking assist
guidelines
CAUTION

When adjusting the guidelines, be sure to park the vehicle
in a safe place and apply the parking brake.
 Before getting out of the car to place the markings, be sure
to turn the ignition switch off (ACC OFF).
 The range projected by the rear view camera is limited.
Also, the vehicle width and distance guidelines displayed
on the rear view camera image may differ from the actual
vehicle width and distance. (The guidelines are straight
lines.)

The image quality may deteriorate depending on the usage
environment, such as at night or in dark surroundings.
1 Park your vehicle in a safe place and apply the
parking brake.
2 Using packing tape or similar, place markings
as follows.
2 m (6 ft. 7 in.)
50 cm (1 ft. 8 in.)
Markings
Markings
Rear bumper
3 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
45
4 Touch [Camera settings].
5 Touch [Parking Assist Guide Adjust].
6 Set the guidelines by dragging the four points.
Adjust the guidelines so that the guidelines can be overlaid to
the markings
p Touch / / / /
necessary. Touch [Default] to reset the settings.

Setting the second camera

You can view images of the second camera (a front camera etc.)
on the screen of this product.
Setting the second camera activation
The default setting is "Off".
p This function is synchronized with "AV Input" setting.
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
45
2 Touch [Camera settings].
3 Touch [2nd Camera Input] to switch "On" or
"Off".
Setting the reversed image
The default setting is "Off".
p This setting is available only when you stop your vehicle in a
safe place and apply the parking brake.
p This function is available when "AV Input" is set to
"Camera" or "2nd Camera Input" is set to "On".
25 cm 1 Display the "System" setting screen.
(9-7/8 in.)
 Refer to Displaying the "System" setting screen on page
45
2 Touch [Camera settings].
3 Touch [2nd Camera: Reverse video] to switch
"On" or "Off".
25 cm
(9-7/8 in.)
Setting the camera for Camera
View mode
To display Camera View at all times, "Camera View" needs to be
set to "On". (The same mode is turned on when
on the camera view screen. The setting value is synchronized.)
The default setting is "Off".
p To set the rear view camera as the camera for Camera View
mode, set "Back Camera Input" to "On".
 Refer to Setting rear view camera activation on page 45
p When using the second camera, set "AV Input" to
"Camera" or "2nd Camera Input" to "On" (both settings are
synchronized).
/ to adjust the guidelines if
is touched