Product Features; Inserting/Replacing The Batteries; Initial Operation - Bosch GLL 2-50 Professional Notice Originale

OBJ_BUCH-817-007.book Page 13 Monday, July 4, 2016 6:35 PM
Cross-line Laser
Shortest pulse duration
Divergence of laser line
Tripod mount
Batteries
Operating time, approx.
Automatic switch-off after approx.
Weight according to
EPTA-Procedure 01:2014
Dimensions
Degree of protection
The measuring tool can be clearly identified with the serial number 9 on
the type plate.

Product Features

The numbering of the product features shown refers to the
illustration of the measuring tool on the graphic page.
1 Exit opening for laser beam
2 Pulse-function indicator
3 Pulse-function button
4 Operating mode button
5 Battery indicator
6 Tripod mount 1/4"
7 On/Off switch
8 Battery lid
9 Serial number
10 Laser warning label
11 Latch of battery lid
12 Alignment plate*
13 0° alignment aid on the alignment plate
14 90° alignment aid on the alignment plate
15 45° alignment aid on the alignment plate
16 Pin on the alignment plate
17 Protective pouch*
18 Case*
19 Laser viewing glasses*
20 Measuring plate with stand*
21 Laser receiver*
* The accessories illustrated or described are not included as
standard delivery.
Assembly

Inserting/Replacing the Batteries

Use only alkali-manganese batteries.
To open the battery lid 8, press the latch of the battery lid 11
in the direction of the arrow and remove the battery lid. Insert
the supplied batteries. When inserting, pay attention to the
correct polarity according to the representation on the inside
of the battery compartment.
Bosch Power Tools
When the battery indication 5 flashes red, the batteries must
GLL2-50
be replaced.
1/1600 s
Always replace all batteries at the same time. Only use batter-
0.5 mrad (full angle)
ies from one brand and with the identical capacity.
1/4"
 Remove the batteries from the measuring tool when
3 x 1.5 V LR6 (AA)
not using it for extended periods. When storing for ex-
tended periods, the batteries can corrode and self-dis-
12 h
charge.
30 min
Operation
0.45 kg
118 x 57 x 89 mm

Initial Operation

IP 54 (dust and splash
 Protect the measuring tool against moisture and direct
water protected)
sun light.
 Do not subject the measuring tool to extreme tempera-
tures or variations in temperature. As an example, do
not leave it in vehicles for a long time. In case of large vari-
ations in temperature, allow the measuring tool to adjust to
the ambient temperature before putting it into operation.
In case of extreme temperatures or variations in tempera-
ture, the accuracy of the measuring tool can be impaired.
 Avoid heavy impact or falling of the measuring tool. Af-
ter heavy exterior impact on the measuring tool, an accura-
cy check should always be carried out before continuing to
work (see "Levelling Accuracy").
 Switch the measuring tool off during transport. When
switching off, the levelling unit, which can be damaged in
case of intense movement, is locked.
Switching On and Off
To switch on the measuring tool, slide the On/Off switch 7 to
the "
ling) or to the "
ic levelling). Immediately after switching on, the measuring
tool sends laser beams out of the exit openings 1.
 Do not point the laser beam at persons or animals and
do not look into the laser beam yourself, not even from
a large distance.
To switch off the measuring tool, slide the On/Off switch 7 to
the "off" position. When switching off, the levelling unit is
locked.
Deactivating the Automatic Shut-off
The measuring tool switches off automatically after an operat-
ing duration of 30 minutes. To deactivate the automatic
switch-off, keep the operating mode button 4 pressed for 3 s
while switching on the measuring tool. When the automatic
switch-off is deactivated, the laser lines briefly flash after 3 s.
 Do not leave the switched-on measuring tool unattend-
ed and switch the measuring tool off after use. Other
persons could be blinded by the laser beam.
To activate the automatic shut-off, switch the measuring tool
off and then on again (without the operating mode button 4
pushed).
on" position (when working without automatic level-
on" position (when working with automat-
1 609 92A 27R | (4.7.16)
English | 13