Maintenance And Inspection - Hitachi G 12SE Mode D'emploi

Once the leading edge of the depressed center
wheel is properly abraded, grinding may be
conducted in either direction.
4. Switch operation
[When the switch has locking mechanism]
Switch ON: To switch on, slide the lock lever in the
direction of A and press the paddle
lever in the direction of B as shown
in Fig. 4-a.
Furthermore, slide the lock lever in the
direction of C shown in Fig. 4-b while
pressing the paddle lever to lock and
enable continuous operation.
Switch OFF: To release the locking mode, press the
paddle lever in the direction of B shown
in Fig. 4-a, and release the paddle lever
to switch off.
[When the switch has no locking mechanism]
To switch on, slide the lock lever in the direction
of A and press the paddle lever in the direction
of B as shown in Fig. 4-a. Release the paddle lever
to switch off.
NOTE:
The paddle lever can not be locked.
5. Precautions immediately after finishing operation
After switching off the machine, do not put it down
until the depressed center wheel has come to a
complete stop. Apart from avoiding serious
accidents, this precaution will reduce the amount
of dust and swarf sucked into the machine.
CAUTION
When the machine is not use, the power source
should be disconnected.
ASSEMBLING AND DISASSEMBLING THE
DEPRESSED CENTER WHEEL (Fig. 1)
CAUTION:
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
1. Assembling (Fig. 1)
(1) Turn the grinder upsidedown so that the spindle
is facing upward.
(2) Mount the wheel washer onto the spindle.
(3) Fit the protuberance of the depressed center wheel
or diamond wheel onto the wheel washer.
(4) Assemble the wheel nut onto the spindle.
(For diamond wheel assembling, use the wheel nut
with the convex side against the diamond wheel.)
(5) Insert the push button to prevent rotation of the
spindle, and tighten the wheel nut with accessory
wrench, as shown in Fig. 1.
2. Disassembling
Follow the above procedures in reverse.
CAUTIONS
Comfirm that the depressed center wheel is mounted
firmly.
Confirm that the spindle lock mechanism is
disengaged by pushing push button two or three
times before switching the grinder on.

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of
cracks and surface defects.
All manuals and user guides at all-guides.com
2. Inspecting the mounting screws:
3. Inspecting the carbon brushes (Fig. 5)
4. Replacing carbon brushes (Fig. 6)
<Disassembly>
(1) Loosen the D4 tapping screw retaining the tail cover
(2) Use the auxiliary hexagonal wrench or small
(3) Remove the end of the pig-tail on the carbon brush
<Assembly>
(1) Insert the end of the pig-tail of the carbon brush
(2) Insert the carbon brush in the brush holder.
(3) Use the auxiliary hexagonal wrench or small
(4) Mount the tail cover and tighten the D4 tapping
5. Maintenance of the motor
6. Service parts list
CAUTION
MODIFICATIONS
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
The Motor employs carbon brushes which are
consumable parts. When they become worn to or
near the "wear limit", it could result in motor
trouble. When an auto-stop carbon brush is
equipped, the motor will stop automatically. At that
time, replace both carbon brushes with new ones
which have the same carbon brush Numbers shown
in the figure. In addition, always keep carbon brushes
clean and ensure that they slide freely within the
brush holders.
and remove the tail cover.
screwdriver to pull up the edge of the spring that
is holding down the carbon brush. Remove the
edge of the spring toward the outside of the brush
holder.
from the terminal section of brush holder and then
remove the carbon brush form the brush holder.
in the terminal section of brush holder.
screwdriver to return the edge of the spring to the
head of the carbon brush.
screw.
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
A: Item No.
B: Code No.
C: No. Used
D: Remarks
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
English
5