Front Panel; Rear Panel - Numark MIXDECK QUAD Guide D'utilisation Rapide

30. (PLAY) MODE – There are four playback modes:
Single: Plays the selected song, then pauses and cues the next track.
SingleReplay: Repeats the current song until manually stopped.
Random: Plays all songs on the CD in a random order.
Continuous: Plays all songs on the CD in order then repeats at the beginning.
To view file names or ID3 tag information when playing MP3s, hold RECALL / STORE and press (PLAY) MODE.
31. LCD DISPLAY – All information and functions are displayed here. CD text (if available), ID3 tag information and effects
settings are all shown here.

FRONT PANEL

1. HEADPHONES – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring. Headphone output
controls are located on the top panel.
2. MIC INPUT – Connect a 1/4" microphone to this input.
3. MIC GAIN – Adjusts the audio level of the microphone signal.
4. MIC BASS – Adjusts the low (bass) frequencies of the microphone channel.
5. MIC TREBLE – Adjusts the high (treble) frequencies of the microphone channel.
Tip: If you experience feedback when using a microphone at loud levels, try turning down the high frequencies.
6. CROSSFADER (CF) SLOPE – Adjusts the slope of the crossfader curve. Flip switch to the left for a smooth fade
(mixing) or to the right for a sharp cut (scratching).
7. CROSSFADER (CF) MODE – Reverses the assignment of CF Assign A and B on the CROSSFADER.

REAR PANEL

1. POWER BUTTON – Press this to turn the unit on and off.
2. POWER IN – Use the included power adapter to connect the mixer to a power outlet. While the power is switched off,
plug the power supply into the mixer first, then plug the power supply into a power outlet.
3. USB SLAVE – Connect the MIXDECK QUAD to a computer via this USB jack and your MIXDECK QUAD can be used
as a software controller device using USB MIDI protocol. You can also use MIXDECK QUAD as your computer's
soundcard. (Remember to select MIXDECK QUAD as the playback device in your computer's sound settings. You can
use MIXDECK QUAD as a soundcard with or without using it as a software controller.)
4. DECK 1 OUTPUT (RCA) – To use MIXDECK QUAD with timecoded CDs, use standard RCA cables to connect this
output to the interface for your digital DJ software.
5. DECK 2 OUTPUT (RCA) – To use MIXDECK QUAD with timecoded CDs, use standard RCA cables to connect this
output to the interface for your digital DJ software.
6. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the grounding wire to these
terminals. If you experience a low "hum" or "buzz", this could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
7. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the AUX
INPUTS. If you are using phono-level turntables, set this switch to "PHONO" to provide the additional amplification
needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set this switch to "LINE."
8. RECORD OUTPUT (RCA) – Use standard RCA cables to connect this output to a recording device, such as a CD
recorder or tape deck. The level of this output is based upon pre-master levels.
9. BOOTH OUTPUT (RCA) – Use standard RCA cables to connect this output to a booth monitoring system. The level of
this output is controlled by the BOOTH VOLUME on the top panel.
10. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The level
of this output is controlled by the MASTER VOLUME on the top panel.
11. MASTER OUTPUT (BALANCED) – Connect this low-impedance XLR output to a PA system or powered monitors. The
level of this output is controlled with the MASTER VOLUME on the top panel.
12. USB AUDIO SWITCH – Select to route audio from either PGM/CUE or USB1/USB2. (see the section SETUP WITH
USB for more details).
13. iOS AUDIO SWITCH – Select to route audio from either PGM/CUE MONO or AUX 3 (see the section SETUP WITH
iOS DEVICES for more details).
14. AUX 3 – This 30-pin port receives audio from an iOS device, provides power to an iOS device, and supports Core MIDI
for all controls and parameters of compatible iPad apps, such as Algoriddim djay. To use this feature, please see the
SETUP WITH iOS DEVICES section of this manual.
Note: Only iOS 5 or higher supports Core MIDI. This means MIXDECK QUAD will only control Algoriddim djay if your
iOS device is using iOS 5 or higher. Devices with iOS 4 can only be used with the iOS AUDIO SWITCH set to AUX 3.
2 3
13 12
10
11 11
14
4
5
5
6 7
6 6
5
9 8
9 8
7
7
8
1
4
1
3
2