Energy Saving Settings (Energy Save) - Pioneer PDP-50MXE10 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Under factory default settings, the screen display
contents will change as follows:
Inverse
White mask
Set
image*
display
[ONCE]
[TIME TO
10 minutes
30 minutes
ACTIVATE]
(set in step 7)
Inverse
White mask
Set
image*
display
[REPEAT]
[TIME TO
10 minutes
30 minutes
ACTIVATE]
24 hours
(set in step 7)
This cycle repeats
* The color and brightness of the current image are displayed in
inverse values. The respective RGB color output levels are
inverted, with light areas appearing dark, and dark areas
appearing light.
Notes
÷ When set to [ONCE], after the screen management program
ends, this part of the display will change to the [OFF]
message. If you wish to continue the screen management
program, use the 2/3 buttons to select [ONCE] again, or
change to [REPEAT].
÷ During screen management operation when set to [ONCE] or
[REPEAT], if the display's MAIN POWER switch is turned OFF,
the screen management program will end, and this part of the
display will change to display the message [OFF]. If you wish
to continue the screen management program, use the 2/3
buttons to select [ONCE] or [REPEAT] again.
6
Use the 5/∞ buttons to select [TIME TO
ACTIVATE].
SCREEN MGT.
STATUS
TIME TO ACTIVATE
START
SET
RETURN
7
Use the 2/3 buttons to set the time you wish the
screen management program to begin.
When the 2/3 buttons are pressed, the screen
management operation can be set from 0 to 24 hours,
in 10-minute units.
8
Use the 5/∞ buttons to select [START].
SCREEN MGT.
STATUS
TIME TO ACTIVATE
START
SET
SET
Note
The [SCREEN MGT.] setting affects all input sources.
Power standby mode
Screen management
function ends here
Power
Inverse
standby
image*
mode
10 minutes
:
REPEAT
:
01H00M
MENU
EXIT
:
REPEAT
:
00H10M
MENU
EXIT
9
Press the SET button.
The set value will be stored in memory, and the
screen will return to that shown in step 2.
The timer begins when the SET button is pressed,
and after passage of the time set in step 7, the screen
management program will begin operating.
10
When finished with the setting, press the MENU
button to return to the normal screen image.
Energy saving settings
(ENERGY SAVE)
The power control function allows screen brightness to
be suppressed as a means of lowering power
consumption and reducing display deterioration.
MENU
5/∞
2/3
SET
Main unit operating
Remote control unit
panel
1
Press the MENU button to display the menu
screen.
MENU
PICTURE
SCREEN
:
CONTRAST
:
BRIGHTNESS
:
R.LEVEL
:
G.LEVEL
:
B.LEVEL
:
H.ENHANCE
:
V.ENHANCE
PICTURE RESET
2
Use the 2/3 buttons to select [OPTION].
MENU
PICTURE
SCREEN
LANGUAGE
ENERGY SAVE
SCREEN MGT.
ORBITER
MASK CONTROL
AUTO SET UP MODE
AUTO FUNCTION
AUDIO OUT
Other Operations
MENU
2/3
SET
5/∞
INPUT1
SETUP
OPTION
0
0
0
0
0
0
0
INPUT1
SETUP
OPTION
:
ENGLISH
:
STANDARD
:
OFF
:
OFF
:
ON
:
INACTIVE
:
OFF
:
FIXED
31
En

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Pdp-50mxe11Pdp-50mxe1Pdp-50mxe1-sPdp-43mxe1Pdp-43mxe1-s

Table des Matières