Blade Safety; Health Advice; Personal Protective Equipment (Ppe) - Evolution R255 SMSL Notice Originale

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

www.evolutionpowertools.com
cut-off piece could get wedged against the blade
and thrown violently.
o) Always use a clamp or a fixture designed
to properly support round material such as
rods or tubing. Rods have a tendency to roll
while being cut, causing the blade to "bite" and
pull the work with your hand into the blade.
p) Let the blade reach full speed before
contacting the workpiece. This will reduce
the risk of the workpiece being thrown.
q) If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece
could cause loss of control or damage to the
mitre saw.
r) After finishing the cut, release the switch,
hold the saw head down and wait for the
blade to stop before removing the cut-off
piece. Reaching with your hand near the
coasting blade is dangerous.
s) Hold the handle firmly when making an
incomplete cut or when releasing the switch
before the saw head is completely in the
down position. The braking action of the saw
may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
NOTE: The above warning applies only for
mitre saws with a brake system.

BLADE SAFETY

WARNING: Rotating saw blades are
extremely dangerous and can cause serious
injury and amputation. Always keep fingers
and hands at least 150mm (6") away from
the blade at all times. Never attempt to
retrieve sawn material until the cutting
head is in the raised position, the guard is
fully closed and the saw blade has stopped
rotating. Only use saw blades that are
recommended by the manufacturer and
as detailed in this manual and that comply
with the requirements of EN 847-1.
• Only use genuine Evolution blades rated for
this machine.
• Do not use saw blades that are damaged or
deformed as they could shatter and cause
serious injury to the operator
or bystanders.
• If the table insert becomes damaged or worn
it must be replaced with an identical one
available from the manufacturer.

HEALTH ADVICE

(2.7)
WARNING: If you suspect that paint on
surfaces in your home contains lead seek
professional advice. Lead based paints should
only be removed by a professional and you
should not attempt to remove it yourself.
Once the dust has been deposited on
surfaces, hand to mouth contact can result
in the ingestion of lead. Exposure to even
low levels of lead can cause irreversible brain
and nervous system damage. The young and
unborn children are particularly vulnerable.
WARNING: Some wood and wood type
(2.8)
products, especially MDF (Medium Density
Fibreboard), can produce dust that may be
hazardous to your health. We recommend
the use of an approved face mask with
replaceable filters when using this machine, in
addition to using the dust extraction facility.
PERSONAL PROTECTIVE
(3.6)
EQUIPMENT (PPE)
Hearing protection should be worn in order
to reduce the risk of induced hearing loss.
Eye protection should be worn in order to
prevent the possibility of the loss of sight
from ejected chippings.
Respiratory protection is also advised as some
wood and wood type products especially MDF
(Medium Density Fibreboard) can produce
dust that can be hazardous to your health. We
r
ecommend the use of an approved face mask
with replaceable filters when using this machine
in addition to using the dust extraction facility.
Gloves should be worn when handling blades
or rough material. Heat resistant gloves should
be worn when handling metallic materials
which may be hot. It is recommended that saw
blades should be carried in a holder wherever
practicable. It is not advisable to wear gloves
when operating the mitre saw.
9
EN
ES
DE
FR
IT
PL
PT
RO

Publicité

Table des Matières
loading

Table des Matières