Talk 2 All - Universal Intercom With Different Brand Unit; Compatibility With Midland Bt Line Units; Pairing The Midland Btnext Pro To Bluetooth Devices - Midland BTNEXT PRO Guide D'utilisation

Talk 2 All - Universal Intercom with different brand unit.

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your
Midland BTNEXT PRO to a different brand intercom available on the market.
You can pair a maximum of two not Midland Intercom devices, one on the "Forward"
button and the other one on the Backward button.
› On the Midland BTNEXT PRO enter the setup mode: (with the unit OFF press and
hold down the Middle button about 7 sec. until the Red light is on permanently).
› Keep pressed the "Forward" button or "Backward" button for 7 seconds: the Red and
Blu LED light will start flashing fast, then (while you still keep the button pressed) the
Red and Blu LED lights will change to slow flashing. Now you can release the button.
Talk2All - Universal Intercom
Not Midland Unit
On the other intercom (not Midland brand) follow the procedure to pair to a phone,
because the BTNEXT PRO is paired as a Phone.
If successfully paired the red/blue lights will stop flashing and the blu light will slowly
flash instead.
Attention: remember to switch OFF all the other Bluetooth devices during the pairing pro-
cedure, only the two devices involved in the pairing must be turned on.
To open the "Universal Intercom" communication on the Midland BTNEXT PRO while
you are in "Intercom Mode", press long (3 sec) the Forward button or "Backward" but-
ton (depending on wich button you used for pairing) . On the other intercom just press
the phone redial or voice dial button.
Maybe it will be necessary to press the redial button two times, depending on the model
of the not Midland intercom.
Attention: In order to use the "Talk2All-Universal Intercom" feature the pairing on the
other unit must be done as a phone. The other intercom (not Midland brand) will be able to
be paired to a phone only if two phones are supported.
28
Talk2All -
Universal Intercom Midland
Passenger Unit paired as a phone
You can pair also a Midland unit as Talk2All, that means the pairing must be done as a
phone (one unit use the Talk2All procedure and the other unit use the pairing to "Phone"
procedure).

Compatibility with Midland BT line units

The BTNEXT PRO is compatible with BTX1 PRO, BTX2 PRO, BT Next Conference,
BTX2 FM and BTX1 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTNEXT PRO is compatible with the previous line of Midland BT (BT Next, BTX2
and BTX2) only if updated to firmware version 2014 or later.

Pairing the Midland BTNEXT PRO to Bluetooth devices

The Midland BTNEXT PRO unit can be paired to other Bluetooth devices, like Pho-
ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).
The pairing procedure must be done using the "Volume +" or the "Volume -" buttons.
› Pairing to the "Volume +" button: for Phone with music A2DP stereo, GPS Naviga-
tor with A2DP audio or external mono/Stereo A2DP dongle.
All devices paired to "Volume +" button has higher priority and will interrupt all the other
communication (like Intercom, FM Radio and Music).
› Pairing to the "Volume -" button: for Phone with music A2DP stereo, GPS Naviga-
tor with A2DP audio or external mono/Stereo A2DP dongle.
All devices paired to "Volume -" button are always in active in background during the
Intercom communication.
VOL- (always in background)
› Phone (HFP/A2DP Stereo)
› GPS (HFP/A2DP Stereo)
› Dongle (HFP/A2DP Stereo)
When a device is paired to the "Vol +" or "Vol –" buttons the "Phone" mode is activated.
VOL+ (high priority)
› Phone (HFP/A2DP Stereo)
› GPS (HFP/A2DP Stereo)
› Dongle (HFP/A2DP Stereo)
www.midlandeurope.com