Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Dust collection
Collected sawdust from coated
WARNING
(polyurethanes, linseed oil, etc.)
workpieces can self-ignite in the dust bag or
elsewhere and cause fire. To reduce the risk of
fire, empty the dust bag frequently and never
store or leave a saw without totally emptying its
dust bag.
The dust port at the back of the saw can be con-
nected to a standard workshop vacuum hose or the
included dust bag. Leave the dust bag open to direct
dust down into a garbage can.
To install, push and twist the hose or dust bag onto
the dust port.
Using Face Boards
When using face boards, secure them using the
mounting holes in the fences. Face boards place dis-
tance between the fence and the workpiece, providing
improved support for some workpieces. Workpiece
splintering can be reduced by using face boards.
Selecting, Installing, and Changing Blades
Always use clean, sharp blades. Dull blades tend
to overload the tool, bind, and cause pinching. Use
only 7-1/4" sliding miter saw blades rated at least
5000 RPM.
1. Remove battery pack.
2. Lower the saw head.
3. Raise the lower guard and hold up while raising
the saw head. Let go of the lower guard. The lower
guard will remain up in the blade-changing OPEN
position. WARNING! Be careful not to lower the
guard head while changing the blade; the lower
guard will fall back into place to cover the blade
and could pinch hands and fingers.
4. Press in the spindle lock and rotate the spindle/
blade until the lock engages.
5. Use the wrench to loosen and remove the left-hand
thread blade bolt (clockwise).
6. Remove the outer blade flange and blade. Wipe
the flanges and spindle to remove dust and debris.
Inspect the parts for damage. Replace if needed.
7. Match the arrow direction on the blade with the
arrow direction on the lower guard. Slide the blade
onto the spindle.
8. Install the outer blade flange. The flat side of the
flange must rest against the blade.
9. Press in the spindle lock and rotate the blade until
the lock engages. Insert and securely tighten the
blade bolt (counterclockwise) with the wrench.
10. Move hands out of the guard area and lower
11. Check the clearance between the blade, kerf
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Guard in
blade-changing
WARNING
OPEN position
making adjustments. Do not defeat the guards.
WARNING
during use. Contact with blade will result
in serious injury.
If your hand is placed too close to the saw blade, there
Outer flange
is an increased risk of injury from blade contact. Use
the No Hand Zone indicators to ensure hands are kept
a safe distance from the blade.
No Hand Zone Indicators:
Blade
• No Hands Zone Circle (groove around turntable)
• Fence Hand Holds (notches on top of fences)
Blade bolt
• Hand Stops (used when fence is removed)
Never cross your hand over the intended line of cutting
either in front or behind the saw blade. The proximity
of the spinning saw blade to your hand may not be
obvious and you may be seriously injured. Saw head
may slide/move, putting your safety at risk. Always
wait for the blade to stop completely before raising
the head, moving workpiece or changing settings.
Be cautious of pitchy, knotty, wet or warped work-
pieces. These materials are likely to create pinching
conditions. Workpieces that bow and pinch may
result in kick back. Inspect for and remove nails
before cutting. Always keep blades clean and sharp;
otherwise the blade produces a narrow kerf and is
likely to be pinched by the workpiece. This tool is not
recommended for cutting ferrous metals such as iron
and steel. See Applications for a more complete list
of materials that can be cut.
6
the saw head. The lower guard will fall back into
place; verify it moves freely.
plate, and fences. Always use the kerf plate. Kerf
plates reduce tear-out and splintering along the
cut by providing edge support.
Recharge only with the charger
specified for the battery. For spe-
Removing/Inserting the Battery
Always remove battery pack before
changing or removing accessories.
Only use accessories specifically
recommended for this tool. Others
ADJUSTMENTS
Always remove the battery pack
before changing accessories or
No Hand Zone
Keep hands out of the No
Hands Zone at all times
Select the Workpiece Carefully
Publicité
Table des Matières
